Intersmooth 7465HS SPC Tin-free Self-polishing Copolymer Antifouling Paint belongs to Antifouling. Specifically designed for ocean-going vessels. A high-solids, high-performance, tin-free, low-friction self-polishing copolymer (SPC) antifouling paint. Parameters on this page: volume solids 54% ± 2%, dry film thickness 200 µm, theoretical spreading rate 2.7 m²/L. Comparable models from the same brand: Intercept 7000 Linear Polishing Antifouling, Intercept 8500 LPP Tin-free Linear Polishing Polymer Antifouling, Interflex 8700 SPC Tin-free Self-polishing Copolymer Antifouling.
Parameter source: International INTERNATIONAL original technical data sheet (TDS) "Intersmooth 7465HS SPC Tin-free Self-polishing Copolymer Antifouling Paint"; values such as spreading rate are converted from TDS parameters and are for model selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 54% ± 2% |
|---|---|
| Dry Film Thickness | 200 µm |
| Theoretical Spreading Rate | 2.7 m²/L |
| VOC | 425 g/L (as supplied) (EPA Method 24), 226 g/kg (… |
| Density / Specific Gravity | — |
| Number of Components | One-component |
| Mixing Ratio | N/A |
| Colour / Appearance | BEA774-Brown, BEA777-Red BEA764-Brown, BEA7... |
| Gloss | N/A |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A high-solids, high-performance, tin-free, low-friction, self-polishing copolymer (SPC) antifouling. Particularly suitable for areas where solvent emissions must be reduced.
Specifically designed for ocean-going ships.
For newbuilding.
| Colour | BEA774-Brown, BEA777-Red BEA764-Brown, BEA767-Red (only available in non-regulated European countries) |
|---|---|
| Topcoat/gloss | N/A |
| Component B (curing agent) | N/A |
| Volume Solids | 54% ±2% (ISO 3233:1998) |
| Mixing ratio | N/A |
| Standard film thickness | May be specified at 75–200 µm DFT (139–370 µm WFT), depending on the end use. |
| Theoretical Spreading Rate | Theoretical spreading rate at 75–200 µm DFT is 7.2–2.7 m²/L, allowing for a suitable loss factor |
| Application Methods | Airless spray, brush, roller |
| Flash Point | Single-component 25 °C |
| Drying data | -5°C | 5°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 120 min | 60 min | 40 min | 30 min |
| Before launching | 30 h | 12 h | 10 h | 8 h |
| Note | For newbuilding, when multiple coats are applied in dock before launch, the pre-launch time shall be extended as follows: 48 h at -5°C, 36 h at 5°C, 24 h at 25°C, 12 h at 35°C. |
|---|---|
| Recoat data — see the “Limitations” section | Substrate Temperature |
| When recoating the following products | -5 °C minimum | -5 °C maximum | 5 °C minimum | 5 °C maximum | 25 °C minimum | 25 °C maximum | 35 °C minimum | 35 °C maximum |
| Intersmooth 7465HS | 12 h | 6 months | 6 h | 6 months | 4 h | 6 months | 3 h | 6 months |
SPC
| Note | For recoating at -5°C, the minimum recoat interval between coats of a three-coat system is 24 h. |
|---|
| Volatile Organic Compounds | 425 g/L (as supplied) (EPA Method 24) 226 g/kg (as supplied liquid paint). EU Solvent Emissions Directive (Council Directive 1999/13/EC) 400 g/L China National Standard GB23985. VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|
Coating hazards GB 30981.2-S-Pb≤1000-NC; complies with GB 30981.2-2025
| US EPA | This product is not registered in the USA or Canada. |
|---|
This product contains no organotin compounds acting as biocides and complies with the international treaty adopted by the IMO in October 2001 on the control of harmful antifouling systems on ships (IMO document AFS/CONF/26).
When used as part of an approved scheme, this product holds the following certificates: the product has been approved by the following classification societies in accordance with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • Bureau Veritas • DNV • Lloyds Register. For details, consult the local International Paint representative.
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
For newbuilding, Intersmooth 7465HS SPC shall always be applied over the recommended primer. The primer surface shall be dry and free from all contaminants; Intersmooth 7465HS SPC shall be applied within the specified recoat interval (refer to the relevant product data sheet). Areas of damage or defect shall be prepared to the specified standard (e.g. Sa2.5 (ISO 8501-1:2007)) and primed before application of Intersmooth 7465HS SPC.
For specific advice, consult your local International Paint representative.
This coating is a single-component product; stir thoroughly with a power mixer before application.
International GTA007. Normally no thinning is required. Under extreme conditions, consult your local representative for application advice. Do not thin beyond the limits of local environmental regulations.
Recommended nozzle size 0.54–0.8 mm (21–31 thou); total output fluid pressure at the nozzle not less than 190 kg/cm² (2700 psi)
Conventional spray application is not recommended.
Brush application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Roller application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Use a cleaning solvent that complies with local regulations. Consult the local representative for specific recommendations.
Flush all equipment thoroughly with International thinner. All unused paint must be stored in tightly closed containers. Partly filled containers may show skinning and/or increased viscosity after storage. Strain the paint before use.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; China — tel. (86) 532 83889090; other regions — contact the regional office.
The service life of the coating is directly proportional to the applied thickness. Product performance depends on achieving the specified film thickness.
After immersion, the colour of Intersmooth 7465HS SPC may change slightly.
Intersmooth 7465HS SPC may be applied to substrates at temperatures as low as -15°C. Before application at temperatures below -5°C, consult the local International Paint representative for detailed application procedures.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
| Packaging Specifications | Component A volume; packaging |
|---|---|
| 20 L | 20 L. For other packaging sizes, consult International Paint. |
| Packaging Specifications | Packaging weight |
|---|---|
| 20 L | 38.6 kg |
| Shelf life | 12 months at all temperatures, after which re-inspection is required. Store in a cool, dry place away from heat and ignition sources. |
|---|
Please consult INTERNATIONAL.
The information given in this product data sheet is not exhaustive. Anyone who uses, for any reason, any product other than those specifically recommended in this data sheet without first obtaining our written confirmation does so at their own risk as regards the suitability of the product for the intended purpose. Although we make every effort to ensure that all advice we give about the product (whether in this data sheet or otherwise) is correct, we cannot control the quality or condition of the substrate, nor the many factors affecting the application and use of this product. Accordingly, unless we specifically agree otherwise in writing, we accept no liability, to the maximum extent permitted by law, for any product performance problem arising, or for any loss or damage caused by use of the product. We therefore disclaim all warranties, express or implied, arising by operation of law or otherwise, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. All products supplied and all technical guidance provided are subject to our terms and conditions of sale. You should obtain a copy of this document and read it carefully. The information contained in this product data sheet may be amended at any time in the light of experience and of our continuing product development policy. Before using the product, it is the user's responsibility to check with the local representative that the data sheet in their possession is the latest version.
This technical data sheet is also available on our websites www.international-marine.com and www.international-pc.com, and should be consistent with this document. If there is any discrepancy between this document and the version of the technical data sheet on the website, the version on the website shall prevail.
© AkzoNobel, 2026www.international-marine.com
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
The factory item numbers of Intersmooth 7465HS SPC Tin-free Self-polishing Copolymer Antifouling Paint are as follows.Item No.is the most accurate form when ordering;Colour/colour codecorresponds to the actual colour (RAL, GSB are colour chart codes);Packaging SpecificationsFactory complete-set specification format. Colors not listed may be ordered against the colour card.
| Item No. | Colour / colour code | Packaging Specifications |
|---|---|---|
| BEA777 Red | — | 20 L |
| BEA774 Brown | — | 20 L |
This model has a total of2item numbers, all listed on this page; colours outside the table (including special colours and bulk packaging) can be confirmed by phone, delivery dates are advised according to the factory's current production schedule and stock. In the packaging specification, the "+" indicates the complete-set notation for two-component products (base + curing agent), subject to the factory specification; a "—" in the colour column denotes an auxiliary product, or that the item has no colour code in the factory system.
