Intercept 7000 Linear Polishing Antifouling belongs to antifouling coatings. Used for newbuilding as well as repair and maintenance. A low-friction linear polishing antifouling containing the proprietary Lubyon® patented technology. Parameters on this page: volume solids 60% ± 2%, dry film thickness 150 µm, theoretical spreading rate 8.0–4.0 m²/L. Comparable models from the same brand: Intercept 8500 LPP Tin-free Linear Polishing Polymer Antifouling, Interflex 8700 SPC Tin-free Self-polishing Copolymer Antifouling, Intersleek 1001 Elastomeric Foul-release Coating.
Parameter source: International manufacturer technical data sheet (TDS) “Intercept 7000 Linear Polishing Antifouling”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 60% ± 2% |
|---|---|
| Dry Film Thickness | 150 µm |
| Theoretical Spreading Rate | 8.0–4.0 m²/L |
| VOC | 362 g/L (as supplied) (EPA Method 24) 205 g/kg (… |
| Density / Specific Gravity | — |
| Number of Components | One-component |
| Mixing Ratio | N/A |
| Colour / Appearance | LPA714-Brown, LPA717-Red Note: Felling and Damman manufacturing locations… |
| Gloss | N/A |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A low-friction linear polishing antifouling paint containing proprietary Lubyon® technology.
Specifically designed for ocean-going ships.
For newbuilding, and maintenance and repair.
| Colour | LPA714-Brown, LPA717-Red Note: When supplied from Felling and Damman manufacturing sites, the above codes will be replaced by LPA724-Brown and LPA727-Red. |
|---|---|
| Topcoat/gloss | N/A |
| Component B (curing agent) | N/A |
| Volume Solids | 60% ±2% (ISO 3233:1998) |
| Mixing ratio | N/A |
| Standard film thickness | May be specified at 75–150 µm DFT (125–250 µm WFT), depending on the end use. |
| Theoretical Spreading Rate | Theoretical spreading rate at 75–150 µm DFT is 8.0–4.0 m²/L, allowing for a suitable loss factor |
| Application Methods | Airless spray, brush, roller |
| Flash Point | Single-component 25 °C |
| Drying data | -5°C | 5°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 6 h | 4 h | 2.5 h | 2 h |
| Before launching | 30 h | 12 h | 8 h | 7 h |
| Note | During major repair or repair, if the antifouling system includes any single coat exceeding 150 µm and/or a total film thickness exceeding 300 µm, at temperatures of 5 °C–20 °C the time before launching must be increased to 24 h, and at temperatures not lower than 25 °C the time before launching must be increased to 18 h. |
|---|---|
| Recoat data — see the “Limitations” section | Substrate Temperature |
| When recoating the following products | -5 °C minimum | -5 °C maximum | 5 °C minimum | 5 °C maximum | 25 °C minimum | 25 °C maximum | 35 °C minimum | 35 °C maximum |
| Intercept 7000 | 20 h | 6 months | 12 h | 6 months | 6 h | 6 months | 4 h | 6 months |
| Volatile Organic Compounds | 362 g/L (as supplied) (EPA Method 24) 205 g/kg (as supplied liquid paint). EU Solvent Emissions Directive (Council Directive 1999/13/EC) 382 g/L China National Standard GB23985. The volatile organic compound values are typical values and are provided for reference only. They may change with factors such as colour and normal manufacturing tolerances. This product does not contain organotin as a biocide and complies with the international treaty adopted in October 2001 by the International Maritime Organization on the control of harmful antifouling systems on ships (IMO Document AFS/CONF/26). |
|---|
Coating hazards GB 30981.2-S-Pb≤1000-NC; complies with GB 30981.2-2025
When used as part of an approved scheme, this product holds the following certificates: The product has been approved by the following classification societies in accordance with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • Bureau Veritas • Lloyds Register • DNV • Korean Register of Shipping. Approval by external bodies may depend on the formulation and/or the manufacturing plant; for details, consult the local International (International Paint) representative.
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
Newbuilding Intercept 7000 shall always be applied over the recommended primer. The primer surface shall be dry and free from any contaminants, and Intercept 7000 must be applied within the specified recoat interval (refer to the relevant product data sheet). Areas with damage, defects and other conditions shall be prepared to the specified standard (for example: Sa2.5 (ISO 8501-1:2007)), and primed before application of Intercept 7000.
When high-pressure fresh water washing is carried out in dry dock prior to newbuilding delivery, consult the local representative. Major repair: Intercept 7000 shall always be applied over the recommended primer. The primer surface shall be dry and free from any contaminants; Intercept 7000 must be applied within the specified overcoating interval (refer to the relevant product data sheet).
Areas with damage, defects and other conditions shall be prepared to the specified standard (for example: SSPC-SP10), and primed before application of Intercept 7000.
Repair: Intercept 7000 applied over itself: as soon as the vessel enters dry dock, before it dries, use a fan-shaped spray gun close to the surface to spray dense high-pressure fresh water (3,000 psi, 211 kg/cm²) to wash and clean the entire area. Refer to the recommended anti-corrosive primer system and apply Intercept 7000 within the overcoating interval specified for the primer (refer to the relevant primer product data sheet).
Application of Intercept 7000 over International (International Paint) Wuxi antifouling paint, International (International Paint) Intersmooth SPC antifouling paint or competitors' antifouling paints: for specific recommendations, consult the local International (International Paint) representative.
Note: for the marine environment in North America, the following surface preparation standard may be used: SSPC-SP10 in place of Sa 2.5 (ISO 8501-1:2007)
This coating is a single-component product; stir thoroughly with a power mixer before application.
International GTA007. Normally no thinning is required. Under extreme conditions, consult your local representative for application advice. Do not thin beyond the limits of local environmental regulations.
Recommended nozzle size 0.54–0.8 mm (21–31 thou); total output fluid pressure at the nozzle not less than 190 kg/cm² (2700 psi)
Conventional spray application is not recommended.
Brush application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Roller application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Flush all equipment thoroughly with International thinner. All unused paint must be stored in tightly closed containers. Partly filled containers may show increased viscosity after storage. Strain the paint before use.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; China — tel. (86) 532 83889090; other regions — contact the regional office.
The service life of the coating is directly proportional to the applied thickness. Product performance depends on achieving the specified film thickness.
After immersion, the colour of Intercept 7000 may change slightly.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
Packaging size volume; packaging
| 20 L | 20 L. For other packaging sizes, consult International Paint. |
|---|
| Packaging Specifications | Packaging weight |
|---|---|
| 20 L | 37.4 kg |
| Shelf life | 12 months at all temperatures. Re-inspection required thereafter. Store in a cool, dry place, away from heat and ignition sources. |
|---|
LPA712-Blue and LPA719-Black are supplied only in Singapore and Indonesia
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
