Intersleek 1100SR Advanced Polymer Foul-release Coating is an antifouling paint. Used for newbuildings or repair and maintenance. An advanced fluoropolymer foul-release coating for slime control. Parameters on this page: volume solids 72% ± 2%, dry film thickness 200 µm, theoretical spreading rate 4.80–3.60 m²/L. Comparable products of the same brand: Intercept 7000 Linear Polishing Antifouling Paint, Intercept 8500 LPP Tin-free Linear Polishing Polymer Antifouling Paint, Interflex 8700 SPC Tin-free Self-polishing Copolymer Antifouling Paint.
Data source: International original Technical Data Sheet (TDS), "Intersleek 1100SR Advanced Polymer Foul-release Coating"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 72% ± 2% |
|---|---|
| Dry Film Thickness | 200 µm |
| Theoretical Spreading Rate | 4.80–3.60 m²/L |
| VOC | 240 g/L (neat) (EPA Method 24) 238 g/kg(… |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B : Component C = 9:2:1 (by volume) |
| Colour / Appearance | FXA991-grey, FXA992-blue, FXA997-red, FX… |
| Gloss |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
An advanced fluoropolymer foul-release coating for slime control.
For newbuilding or maintenance and repair.
| Colour | FXA991-grey, FXA992-blue, FXA997-red, FXA999-black and a limited range of other colours |
|---|---|
| Topcoat/gloss | Gloss |
| Component B (curing agent) | FXA993 (Component B), FXA994 (Component C) |
| Volume Solids | 72% ±2% (ISO 3233:1998) |
| Mixing ratio | Component A : Component B : Component C = 9:2:1 (by volume) |
| Standard film thickness | Can be specified at 150–200 µm dry film (208–278 µm wet film), depending on the final use. |
| Theoretical Spreading Rate | In the 150–200 µm dry film range, the theoretical spreading rate is 4.80–3.60 m²/L, allowing an appropriate loss factor. |
| Application Methods | Airless spray, brush |
| Flash Point | Component A 46 °C; Component B 22 °C; Component C 36 °C; mixed 33 °C |
| Induction Time | Not required |
| Drying data | 0°C | 15°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 5 h | 3 h | 2 h | 60 min |
| Hard dry [ISO 9117-1:2009] | 15 h | 6 h | 4 h | 2 h |
| Before launching | 48 h | 36 h | 20 h | 17 h |
| Pot life after mixing | 140 min | 90 min | 60 min | 30 min |
| Note | Between 5 °C and 20 °C, the interval before launching may be reduced to 24 hours, provided the vessel berths for at least 2–3 days after launching. Between 0 °C and 5 °C, the minimum time before launching is 48 hours, and the vessel shall berth for at least 4 days after leaving dry dock. However, the coating may delaminate in any areas subject to mechanical wear (for example, from fendering or impact damage). |
|---|
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 0°C | 15°C | 25°C | 35°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Note | May be overcoated with itself, both on fresh coatings and on coatings after prolonged immersion, provided the surface is in good, clean condition. Consult International Paint. |
|---|
| Volatile Organic Compounds | 240 g/L (neat) (EPA Method 24) 238 g/kg (neat liquid paint). EU Solvent Emissions Directive (Commission Directive 1999/13/EC) 252 g/L China national standard GB 23985. VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|
This product contains no organotin compounds acting as biocides and complies with the international treaty adopted by the IMO in October 2001 on the control of harmful antifouling systems on ships (IMO document AFS/CONF/26).
When used as part of an approved system, this product holds the following certificates: the product has been approved by the following classification societies as compliant with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • Bureau Veritas • DNV GL • Lloyd's Register • Korean Register of Shipping. For details, consult your local International Paint representative.
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
Intersleek 1100SR must always be applied over the Intersleek tie coat within the specified overcoating interval.
For detailed application advice, consult International Paint.
The coating is supplied in three containers as one unit. Always mix the entire unit in the supplied ratio.
(1) Stir Component A with a power mixer.
(2) Mix all of Component A with Component B and stir thoroughly with a power mixer.
(3) Add all of Component C and stir thoroughly with a power mixer.
Carefully (with slow power stirring) add Component C to the Component A/Component B mixture. These products are moisture-sensitive and shall be opened only when needed.
Not recommended. Only in special cases, use International GTA007. Do not thin beyond the limits of local environmental regulations.
Recommended nozzle size 0.38–0.53 mm (15–21 thou); total output fluid pressure at the nozzle not less than 211 kg/cm² (3000 psi)
Conventional spray application is not recommended.
Brush application is recommended only for repair areas. Multiple coats may be required to achieve the specified film thickness.
Roller application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
International GTA007/GTA822
Do not leave paint in hoses, spray guns or spray equipment. Flush all equipment thoroughly with International GTA007/GTA822. Once a kit of paint is mixed, it should not be resealed; if the interruption during application is too long, it is recommended to re-mix the components before restarting application.
All equipment should be cleaned with International GTA007/GTA822 immediately after use. Flushing the spray equipment periodically during the day is good working practice. The number of cleanings depends on spray volume, temperature and use time (including delays). Do not exceed the pot life of the paint.
All surplus paint and empty containers must be disposed of in accordance with appropriate local regulations/laws.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; China — tel. (86) 532 83889090; other regions — contact the regional office.
The minimum acceptable substrate temperature for application is 0 °C. A minimum relative humidity of 30% is required to ensure proper curing. Below 30% relative humidity, longer curing times are required.
Take care to avoid overspray on other coated areas.
Intersleek 1100SR must be applied over the Intersleek tie coat within the specified overcoating interval.
Before use or before using other coatings, all equipment must be thoroughly cleaned to prevent contamination. Liquid cleaners not permitted for Intersleek 1100SR must not contaminate other paints.
Measures shall be taken to prevent silicone contamination of adjacent areas.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
| Packaging Specifications | Component A | Component B | Component C | |||
| Volume | Packaging | Volume | Packaging | Volume | Packaging | |
| 10 L | 7.5 L | 10 L | 1.67 L | 2.5 L | 0.83 L | 1 L |
| 5 US gal | 3.75 US gal | 5 US gal | 0.83 US gal | 1 US gal | 0.42 US gal | 0.5 US gal |
Component C is supplied in polyethylene containers. For other package sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 10 L | 12.2 kg |
| 5 US gal | 48.3 lb |
| Shelf life | At 25 °C, minimum 12 months. Thereafter, re-inspection is required. Store in a dry, sheltered place away from heat and sources of ignition. |
|---|
Please consult INTERNATIONAL.
The information given in this product data sheet is not exhaustive. Anyone who uses, for any reason, any product other than those specifically recommended in this data sheet without first obtaining our written confirmation does so at their own risk as regards the suitability of the product for the intended purpose. Although we make every effort to ensure that all advice we give about the product (whether in this data sheet or otherwise) is correct, we cannot control the quality or condition of the substrate, nor the many factors affecting the application and use of this product. Accordingly, unless we specifically agree otherwise in writing, we accept no liability, to the maximum extent permitted by law, for any product performance problem arising, or for any loss or damage caused by use of the product. We therefore disclaim all warranties, express or implied, arising by operation of law or otherwise, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. All products supplied and all technical guidance provided are subject to our terms and conditions of sale. You should obtain a copy of this document and read it carefully. The information contained in this product data sheet may be amended at any time in the light of experience and of our continuing product development policy. Before using the product, it is the user's responsibility to check with the local representative that the data sheet in their possession is the latest version.
This technical data sheet is also available on our websites www.international-marine.com and www.international-pc.com, and should be consistent with this document. If there is any discrepancy between this document and the version of the technical data sheet on the website, the version on the website shall prevail.
© AkzoNobel, 2019www.international-marine.com
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
