Interline 605 Inorganic Zinc Silicate is an inorganic zinc silicate paint. A tank coating suitable for carrying petroleum products, solvents (including methanol) and other neutral cargoes. A two-component zinc silicate coating. Parameters on this page: volume solids 62% ± 2%, dry film thickness 125 µm, theoretical spreading rate 4.96 m²/L. Comparable products of the same brand: Interline 344 Inorganic Zinc Tank Coating, Intercept 7000 Linear Polishing Antifouling, Intercept 8500 LPP Tin-free Linear Polishing Polymer Antifouling.
Data source: International original Technical Data Sheet (TDS), "Interline 605 Inorganic Zinc Silicate"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 62% ± 2% |
|---|---|
| Dry Film Thickness | 125 µm |
| Theoretical Spreading Rate | 4.96 m²/L |
| VOC | 527 g/L calculated value. VOC values are typical values provided for reference only… |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B = 3.34:1 (by volume) |
| Colour / Appearance | QHA105 green |
| Gloss | N/A |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A two-component zinc silicate coating.
A tank coating suitable for carrying petroleum products, solvents (including methanol) and other neutral cargoes.
For newbuilding or maintenance and repair.
| Colour | QHA105 green |
|---|---|
| Topcoat/gloss | N/A |
| Component B (curing agent) | QHA104 (zinc powder) |
| Volume Solids | 62% ±2% (ISO 3233:1998) |
| Mixing ratio | Component A : Component B = 3.34:1 (by volume) |
| Standard film thickness | 125 µm dry film thickness (202 µm wet film thickness) |
| Theoretical Spreading Rate | At 125 µm dry film thickness, the theoretical spreading rate is 4.96 m²/L, allowing an appropriate loss factor. |
| Application Methods | Airless spray, brush, conventional spray, roller |
| Flash Point | Component A 13 °C; Component B not applicable; mixed 13 °C |
| Induction Time | Not required |
| Drying data | 5°C | 10°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 45 min | 40 min | 30 min | 10 min |
| Hard dry [ISO 9117-1:2009] | 4 h | 3 h | 2 h | |
| Pot life after mixing | 8 h | 7 h | 6 h | 4 h |
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 5°C | 10°C | 25°C | 35°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Interline 605 | 4 h | 10 days | 3 h | 10 days | 2 h | 10 days | 2 h | 10 days |
| Volatile Organic Compounds | 527 g/L calculated value. VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
On newbuildings, remove weld spatter and grind welds and sharp edges smooth where required.
This product must be applied only on surfaces abrasive blast cleaned to Sa 2.5 (ISO 8501-1:2007).
A jagged surface roughness of 30–50 µm is recommended.
Interline 605 must be applied before the steel oxidizes. If oxidation has indeed occurred, the entire oxidized area shall be re-blasted to the standard specified above.
For specific recommendations, consult International Paint.
Note: for the marine environment in North America, the following surface preparation standard may be used: SSPC-SP10 in place of Sa 2.5 (ISO 8501-1:2007)
Interline 605 is supplied in two components: a liquid binder component (Component A) and a powder component (Component B). Under mechanical stirring, slowly add the powder (Component B) to the liquid binder (Component A). Do not add the liquid to the powder. The coating should be filtered before application, and the paint in the can should be stirred continuously during spraying. Once mixed, a batch must be used within the specified pot life.
Interline 605 contains metallic zinc; stir thoroughly during application to ensure uniformity.
Only in special cases, use International GTA415. Do not thin beyond local environmental regulations.
Recommended nozzle size 0.46–0.61 mm (18–24 thou); total output fluid pressure at the nozzle not less than 141 kg/cm² (2010 lb/in²)
Suitable.
Use suitable dedicated equipment. Thinning may be required.
Brush application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Roller application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Do not leave paint in hoses, spray guns or spray equipment. Flush all equipment thoroughly with International thinner. Once mixed, paint should not be resealed; if work is interrupted for too long, mix a fresh batch before resuming application.
All equipment shall be cleaned with International thinner immediately after use. Periodically flushing spray equipment during the working day is good practice. The frequency of cleaning depends on the quantity sprayed, temperature, relative humidity and elapsed time (including delays). Do not exceed the pot life of the mixed paint.
All surplus paint and empty containers must be disposed of in accordance with appropriate local regulations/laws.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; other regions — contact the regional office
Consult International Paint to determine whether Interline 605 is suitable for the cargo to be carried. Drying times and overcoating intervals may vary due to site factors such as compartment shape or ventilation rate.
For the required interval between completion of coating and cargo loading, refer to the detailed coating application procedure.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
| Packaging Specifications | Component A | Component B | ||
| Volume | Packaging | Volume | Packaging | |
| 18 L | 13.85 L | 20 L | 4.15 L | 10 L |
For other packaging sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 18 L | 46.9 kg |
12 months at 25 °C. Thereafter, re-inspection is required. Store in a cool, dry place away from heat and sources of ignition.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
