5984 CMP BIOCLEAN R silicone antifouling coating is an antifouling coating of the silicone system. Parameters on this page: volume solids 65 ± 2% (ISO 3233), dry film thickness 200 µm, theoretical spreading rate 0.308 L/m². Comparable products from the same brand: 5981B CMP BIOCLEAN PLUS silicone antifouling coating, 5982 CMP BIOCLEAN HB silicone antifouling coating, 5986B CMP BIOCLEAN UNDERCOAT PLUS silicone antifouling coating.
Parameter source: original manufacturer technical data sheet (TDS) '5984 CMP BIOCLEAN R Silicone Antifouling Coating' from CMP; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 65 ± 2% (ISO: 3233) |
|---|---|
| Dry Film Thickness | 200 µm |
| Theoretical Spreading Rate | 0.308 L/m2 |
| VOC | 325 g/L (Method 24) |
| Density / Specific Gravity | 1.04 g/ml (ISO: 2811) |
| Number of Components | One-component |
| Flash Point | 26.5°C |
| Thinner | SILICON THINNER A, EPOXY THINNER A(… |
| Colour / Appearance | Light grey, red-brown |
CMP BIOCLEAN R is a one-component silicone antifouling coating.
| Type | Silicone antifouling |
|---|---|
| Use | Used as the topcoat of the CMP BIOCLEAN system, specially designed for rudders and propellers of ocean-going vessels and fast coastal vessels. |
| Colour | Light grey, red-brown |
|---|---|
| Flash Point | 26.5°C |
| Density | 1.04 g/ml (ISO: 2811) |
| Volume Solids | 65 ± 2% (ISO: 3233) |
| Volatile organic compound content | 325 g/L (Method 24) |
| Theoretical spreading rate | 0.308 L/m2 |
| Thickness | WFT 308 µm |
| Dry film | 200 µm |
(DFT = 200 µm) Drying time
| Temperature | 0 °C | 5 °C | 10 °C | 20 °C | 30 °C |
| Surface Dry | 10 h | 6 h | 3 h | 2 h | 1 h |
| Hard Dry | 20 h | 14 h | 10 h | 7 h | 5 h |
| Recoat interval | Minimum; maximum |
|---|---|
| Minimum launching interval | 38 h 24 h 20 h 14 h 8 h |
| Application method | Airless spray, brush |
|---|---|
| Weather: temperature | 0-35°C |
| Humidity | 40-85% RH |
| Airless spray: viscosity | - |
| Nozzle | Graco519 - 721 |
| Paint output pressure | 20.0 Mpa |
| Spray gun speed | 60–80 cm/s |
| Thinner | SILICON THINNER A, EPOXY THINNER A (for cleaning only) |
| Thinning | -% by volume |
| Preceding coat | CMP BIOCLEAN SG-R, CMP BIOCLEAN SG (for rudders only) |
| Subsequent coat | - |
| Packaging | One-component |
3. Stir with a mixer until homogeneous, then add the appropriate thinner and mix.
4. Under normal conditions, thinner is not recommended.
5. Density, volume solids, and VOC content are theoretical calculated values excluding thinner. These values vary with colour, production process, and local regulations.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
