5526C UNY MARINE HS M Polyurethane Topcoat belongs to polyurethane coatings and is used as a topcoat. UNYMARINE HS M is a high-solids topcoat based on acrylic resin and non-yellowing polyisocyanate resin and offers the following advantages: 1. Good durability even when applied over rough surfaces for long periods. Parameters on this page: volume solids 66 ± 2% (ISO: 3233), dry film thickness 50-75 µm, theoretical spreading rate 0.076-0.114 L/m2. Comparable models from the same brand: 5510B THERMO SHADAN PU Polyurethane Topcoat, 5526 UNY MARINE HS Polyurethane Topcoat, 100 EVASIGN No.100 Modified Alkyd Resin Topcoat.
Parameter source: CMP original technical data sheet (TDS) "5526C UNY MARINE HS M Polyurethane Topcoat"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 66 ± 2% (ISO: 3233) |
|---|---|
| Dry Film Thickness | 50–75 µm |
| Theoretical Spreading Rate | 0.076-0.114 L/m2 |
| VOC | 314 g/L (Method 24) |
| Density / Specific Gravity | 1.39 g/ml (ISO: 2811) |
| Number of Components | Two-component |
| Thinner | URETHANE THINNER A |
| Mixing Ratio | Base : curing agent = 88:12 (by volume) |
| Colour / Appearance | White or specified colours |
UNYMARINE HS M is a high-solids topcoat based on acrylic resin and non-yellowing polyisocyanate resin
It has the following advantages: 1. Good durability even when applied over a coating on a rough surface for a long time.
2. Good weather resistance (gloss retention).
3. Good adhesion to the previous coat.
4. Good physical properties such as toughness, impact resistance and abrasion resistance.
5. Good oil and chemical resistance.
6. Recoatable.
| Type | Polyurethane topcoat |
|---|---|
| Use | Suitable as a high-gloss topcoat for the exterior superstructure, exterior decks and equipment surfaces of steel vessels. |
| Mixing Ratio | Base : curing agent = 88:12 (by volume) |
|---|---|
| Colour | White or specified colours |
| Flash Point | Base component 15.9°C Curing agent 45.9°C |
| Density | 1.39 g/ml (ISO: 2811) |
| Volume Solids | 66 ± 2% (ISO: 3233) |
| Volatile organic compound content | 314 g/L (Method 24) |
| Theoretical spreading rate | 0.076-0.114 L/m2 |
| Thickness | WFT 76-114 µm |
| Dry film | 50–75 µm |
(dry film 70 µm)
| Temperature | -5 °C | 0 °C | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 3.5 h | 2 h | 1 h | 40 min | 30 min | 20 min |
| Hard Dry | 60 h | 40 h | 24 h | 12 h | 8 h | 6 h | |
| Recoat interval | At least | 60 h | 40 h | 24 h | 12 h | 8 h | 6 h |
At most*
| Pot life | 24 h, 24 h, 24 h, 20 h, 16 h, 8 h |
|---|---|
| Induction period | 30 min, 30 min, 30 min, 30 min, 30 min, 30 min |
| Application method | Airless spray, brush, roller |
|---|---|
| Weather: temperature | Minimum -5 °C |
| Humidity | Maximum 85% RH |
| Airless spray: viscosity | 30–50 s (Ford Cup #4) |
| Nozzle | Graco515,615,715 |
| Paint output pressure | 14.7-23.5 Mpa |
| Spray gun speed | 80–100 cm/s |
| Thinner | URETHANE THINNER A |
| Thinning | 0–15% by volume (airless spray) |
The surface to be coated shall be clean and free from rust, dirt, crude oil, grease or other foreign matter, cleaned by power washing, detergent or solvent as appropriate.
| Preceding coat | BANNOH 500, BANNOH 1500, BANNOH 200 and others |
|---|---|
| Subsequent coat | - |
| Packaging | Two-component |
Note: 1 *Contact the CMP sales department.
2 The performance of the curing agent decreases after reaction with moisture; use with caution.
3. Maintain ventilation from application until full cure to remove residual solvent and promote curing.
4 Stir with a mixer until uniform, then add an appropriate thinner and mix.
5 Excessive thinner addition reduces sag resistance and film performance.
6 VOC content and density are theoretically calculated from a representative colour formulation (white) without thinner. Values vary with the formulation of different colours.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
The factory item numbers of 5526C UNY MARINE HS M Polyurethane Topcoat are as follows.Item No.is the most accurate form when ordering;Colour/colour codecorresponds to the actual colour (RAL, GSB are colour chart codes);Packaging SpecificationsFactory complete-set specification format. Colors not listed may be ordered against the colour card.
| Item No. | Colour / colour code | Packaging Specifications |
|---|---|---|
| 5526C UNYMARINE HS M BLUE PB11 | — | 20 L |
| 5526C UNYMARINE HS M ORANGE 2.5YR6 | 14 | 20 L |
| 5526C UNYMARINE HS M 5PB3 | 8 | 20 L |
| 5526C UNYMARINE HS M N85 | — | 20 L |
| 5526C UNYMARINE HS M RAL6010 | — | 20 L |
| 5526C UNYMARINE HS M RAL9010 | — | 20 L |
| 5526C UNYMARINE HS M YELLOW CS-620 | — | 20 L |
| 5526C UNYMARINE HS M RAL9005 | — | 2 L |
| 5526C UNYMARINE HS M RAL7000 | — | 20 L |
| 5526C UNYMARINE HS M White | — | 20 L |
This model has a total of10item numbers, all listed on this page; colours outside the table (including special colours and bulk packaging) can be confirmed by phone, delivery dates are advised according to the factory's current production schedule and stock. In the packaging specification, the "+" indicates the complete-set notation for two-component products (base + curing agent), subject to the factory specification; a "—" in the colour column denotes an auxiliary product, or that the item has no colour code in the factory system.
