2400A EVAMARINE Alkyd Topcoat is an alkyd coating used as a topcoat. EVAMARINE is a coating composed of alkyd resin, with good adhesion, weather resistance and colour retention. Parameters on this page: volume solids 52 ± 2%, theoretical spreading rate 0.048-0.068 L/m², number of components: one-component. Comparable models from the same brand: 100 EVASIGN No. 100 modified alkyd resin topcoat, 2131 ROSWAN QD HB high-build special alkyd primer, 4038G ACRI 700 FINISH G acrylic topcoat.
Parameter source: CMP original technical data sheet (TDS) for 2400A EVAMARINE Alkyd Topcoat; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 52 ± 2% |
|---|---|
| Dry Film Thickness | 25–35 µm |
| Theoretical Spreading Rate | 0.048-0.068 L/m2 |
| VOC | 385 |
| Density / Specific Gravity | 1.24 gq/ml |
| Number of Components | One-component |
| Flash Point | 43°C |
| Thinner | MARINE THINNER |
| Colour / Appearance | White, other specified colours |
HUGUMARINE PAINTST!
| Type | Alkyd Topcoat |
|---|---|
| Use | Can be used as a topcoat for exterior wooden boards and steel plates |
| Colour | White, other specified colours |
|---|---|
| Flash Point | 43°C |
| Density | 1.24 gq/ml |
| Volume Solids | 52±2% |
| Volatile organic compound content | 385 |
| Theoretical spreading rate | 0.048-0.068 L/m2 |
| Thickness | Wet film 48-68 µm |
| Dry film 25-35 | µm |
()
| Temperature | -5°C | 0°C | 5°C | 10°C | 20°C | 30°C | |
| Drying Time | Surface Dry | 8 h | 5 h | 4 h | 3 h | 2 h | 1.5 h |
| Hard Dry | 70 h | 48 h | 30 h | 16 h | 8 h | 6 h | |
| Recoat interval | At least | 120 h | 72 h | 48 h | 24 h | 16 h | 12 h |
At most
| Application method | Airless spray, brush, roller |
|---|---|
| Weather | Temperature: minimum -5 °C |
| Humidity | Maximum 85% RH |
| Apply by airless spray | Viscosity: 110 s (Ford Cup #4) |
| Nozzle | Graco615,715 |
| Paint output pressure | 10.7-13.8 |
| Spray gun speed | 80–100 cm/s |
| Thinner | MARINE THINNER |
| Thinning | 0–7% by volume |
| Preceding coat | LZI PRIMER, RUST INHINITIVE PRIMER Z, ROSWAN QD, BANNOH 200, etc. |
| Subsequent coat | - |
| Packaging | One-component |
Note: 1. To avoid orange peel and wrinkling after the subsequent coat, keep within the recommended film thickness range.
2. In confined spaces or restricted spaces at low temperature, ventilation is necessary to remove volatilised solvent and promote film formation during application and drying.
3. At -10 °C, additional thinner may be required to reach the viscosity required for application.
4. Excessive solvent may reduce sag resistance. 5. Density, volatile organic compound content and volume solids are theoretical values calculated for a representative colour formulation (white) without thinner. The values differ for formulations of different colours.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
The factory item codes of 2400A EVAMARINE Alkyd Topcoat are as follows.Item No.is the most accurate form when ordering;Colour/colour codecorresponds to the actual colour (RAL, GSB are colour chart codes);Packaging SpecificationsFactory complete-set specification format. Colors not listed may be ordered against the colour card.
| Item No. | Colour / colour code | Packaging Specifications |
|---|---|---|
| 2400A EVAMARINE Munsell 7.5BG7 | 2(T57-70D) | 20 L |
| 2400A EVAMARINE Munsell 2.5G8 | 3 | 20 L |
| 2400A EVAMARINE Munsell 7.5PB3 | 10 | 20 L |
| 2400A EVAMARINE N9.5 | — | 20 L |
| 2400A EVAMARINE Munsell 7.5R4 | 14 | 20 L |
| 2400A EVAMARINE RAL7035 | — | 20 L |
| 2400A EVAMARINE Munsell 10YR7.5 | 14 | 20 L |
| 2400A EVAMARINE Munsell 2.5G7 | 2(SEMI-G) | 20 L |
This model has a total of8item numbers, all listed on this page; colours outside the table (including special colours and bulk packaging) can be confirmed by phone, delivery dates are advised according to the factory's current production schedule and stock. In the packaging specification, the "+" indicates the complete-set notation for two-component products (base + curing agent), subject to the factory specification; a "—" in the colour column denotes an auxiliary product, or that the item has no colour code in the factory system.
