A shop (prefabrication) primer for steel protection during fabrication and assembly. Low dry film thickness, two-component, heat-resistant, zinc silicate shop (prefabrication) primer that provides excellent anticorrosive protection (even after heating to 800 °C), with minimal zinc salt formation. Parameters on this page: volume solids 28% ± 2%, dry film thickness 8 µm, theoretical spreading rate 35 m²/L. Comparable products of the same brand and type: Interbond 201 - Low Temperature epoxy primer/topcoat, Intercryl 559 smooth wash-resistant topcoat, Intergard 7020 abrasion-resistant pure epoxy aluminium paint.
Parameter source: International Paint INTERNATIONAL original technical data sheet (TDS) "Interplate 8010 Zinc Silicate Shop (Prefabrication) Primer"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 28% ± 2% |
|---|---|
| Dry Film Thickness | 8 µm |
| Theoretical Spreading Rate | 35 m²/L |
| VOC | 621 g/L (as supplied) (EPA Method 24) 640 g/L China... |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B = 1.00:1.22 (by volume) |
| Colour / Appearance | NQA080 grey, NQA081 green, NQA082 red |
| Gloss | Matt |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Low dry film thickness, two-component, heat-resistant, zinc silicate shop (prefabrication) primer that provides excellent anticorrosive protection (even after heating to 800 °C), with minimal zinc salt formation. It has excellent welding and cutting properties and resists damage caused by welding, gas cutting and fairing; compared with general zinc silicate products, it reduces secondary surface preparation requirements.
A shop (prefabrication) primer for the protection of steel during fabrication and erection.
Suitable for use with impressed current cathodic protection.
For newbuilding.
| Colour | NQA080 grey, NQA081 green, NQA082 red |
|---|---|
| Topcoat/gloss | Matt |
| Component B (curing agent) | NQA086 |
| Volume Solids | 28% ±2% (ISO 3233:1998) |
| Mixing ratio | Component A : Component B = 1.00:1.22 (by volume) |
| Standard film thickness | 8 µm DFT (29 µm WFT) |
| Theoretical Spreading Rate | At 8 µm DFT the theoretical spreading rate is 35 m²/L, allowing for appropriate loss factors |
| Application Methods | Airless spray, brush, conventional spray, roller |
| Flash Point | Component A 14 °C; Component B 13 °C; after mixing 13 °C |
| Induction Time | N/A |
| Drying data | 5°C | 10°C | 25°C | 35°C |
| Hard dry [ISO 9117-1:2009] | 5 min | 3 min | ||
| Pot life after mixing | 24 h | 18 h | ||
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 5°C | 10°C | 25°C | 35°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Note | Consult your local representative; a suitable primer requires at least 24 hours. |
|---|
| Volatile Organic Compounds | 621 g/L (as supplied) (EPA Method 24) 640 g/L China National Standard GB23985. The volatile organic compound values are typical values provided for reference only. They may change with factors such as colour and normal manufacturing tolerances. |
|---|
When used as part of an approved system, this coating holds the following certificates: • Welding quality – approval of prefabrication primer (LR) • Welding quality – shop primer for corrosion protection of steel plates and structures (DNV). For details, consult your local representative.
For the paint system best suited to the surface to be protected, consult your local representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
The shop primer for newbuildings shall be applied with automatic blast/spray equipment.
Blast at least to Sa2.5 (ISO 8501-1:2007) or SSPC-SP10. Blasting is usually carried out with steel grit or a mixture of steel grit with a particle size of 0.6–1.0 mm and steel shot with a particle size of 0.6–1.4 mm to obtain a pronounced angular surface profile.
Apply Interplate 8010 before oxidation occurs. If oxidation has indeed occurred, the entire oxidized area shall be re-blasted to the standard specified above.
Ensure the area is clean and dry before applying Interplate 8010.
For specific advice, consult your local representative.
Note: for the marine environment in North America, the following surface preparation standard may be used: SSPC-SP10 in place of Sa 2.5 (ISO 8501-1:2007)
Interplate 8010 is supplied as two components, a liquid binder component (Component B) and a slurry component (Component A). While mechanically stirring, slowly add the binder (Component B) to the slurry (Component A). Do not add the slurry to the liquid. Filter the paint before application and keep the paint in the can under continuous agitation during spraying. Once a unit of paint has been mixed, it shall be used within the specified pot life. This paint is a low-viscosity paint and requires agitation during application to ensure uniformity.
International GTA810. Normally no thinning is required. Under extreme conditions, consult your local representative for application advice. Do not thin beyond the limits permitted by local environmental regulations.
Recommended nozzle tip size 0.43–0.53 mm (17–21 thou); total fluid output pressure at the nozzle not less than 70–141 kg/cm² (1000–2010 psi)
Use suitable dedicated equipment. Thinning may be required.
Brush application is recommended for small areas only.
Roller application is recommended for small areas only.
International GTA810
Do not allow paint to remain in hoses, spray guns or spray equipment. Flush all equipment thoroughly with International GTA810. Once a unit of paint has been mixed, it shall not be resealed; if the application is interrupted for too long, it is recommended to re-mix the components before resuming application.
All equipment shall be cleaned with International GTA810 immediately after use. Flushing spray equipment at regular intervals during the working day is good working practice. The frequency of cleaning depends on the quantity sprayed, temperature and time in use (including delays). Do not exceed the pot life of the paint.
All surplus paint and empty containers must be disposed of in accordance with appropriate local regulations/laws.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; China — tel. (86) 532 83889090; other regions — contact the regional office.
Drying time depends on the substrate temperature and ventilation.
If the relative humidity is below 50%, curing will be retarded.
When applying Interplate 8010, manual spraying is not recommended.
Shop primer is not recommended as a repair primer after fabrication.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
| Packaging Specifications | Component A | Component B | ||
| Volume | Packaging | Volume | Packaging | |
| 18 L | 8.1 L | 20 L | 9.9 L | 10 L |
For other packaging sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 18 L | 23.45 kg |
| Shelf life | Requires low-flash storage. |
|---|
Component A – 12 months at 25 °C; Component B – 12 months at 25 °C. Re-inspection required thereafter. Store in a cool, dry place away from heat and ignition sources.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
