For newbuilding, repair and maintenance or in-service maintenance. A one-component vinyl emulsion with good flow and high hiding power, a smooth wash-resistant topcoat. Parameters on this page: volume solids 32% ± 2%; dry film thickness 25 µm; theoretical spreading rate 12.80 m²/L. Comparable products from the same brand: Interbond 201 - Low Temperature Epoxy Primer/Topcoat, Intergard 7020 Abrasion-resistant Aluminium Pure Epoxy, Intergard 821 Two-component Epoxy Filler.
Source: INTERNATIONAL original technical data sheet (TDS) 'Intercryl 559 Smooth Wash-resistant Topcoat'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 32% ± 2% |
|---|---|
| Dry Film Thickness | 25 µm |
| Theoretical Spreading Rate | 12.80 m²/L |
| VOC | 16 g/L calculated; 10 g/kg (as supplied liquid paint). EU Solvent Emissions Directive… |
| Density / Specific Gravity | — |
| Number of Components | One-component |
| Mixing Ratio | N/A |
| Colour / Appearance | WGB000 white |
| Gloss | Matt |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A one-component vinyl emulsion with good flow and high hiding power, a smooth wash-resistant topcoat.
For interior areas requiring a high decorative appearance.
For newbuilding, maintenance and repair, or in-service maintenance.
| Colour | WGB000 white |
|---|---|
| Topcoat/gloss | Matt |
| Component B (curing agent) | N/A |
| Volume Solids | 32% ±2% (ISO 3233:1998) |
| Mixing ratio | N/A |
| Standard film thickness | 25 µm dry film thickness (78 µm wet film thickness) |
| Theoretical Spreading Rate | At 25 µm dry film thickness, the theoretical spreading rate is 12.80 m²/L, allowing an appropriate loss factor |
| Application Methods | Brush, conventional spray, roller |
| Drying data | 10°C | 15°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 2 h | 60 min | 30 min | 20 min |
| Hard dry [ISO 9117-1:2009] | 6 h | 3 h | 60 min | 50 min |
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 10°C | 15°C | 25°C | 35°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Intercryl 559 | 16 h | Unlimited | 12 h | Unlimited | 4 h | Unlimited | 3 h | Unlimited |
| Volatile Organic Compounds | 16 g/L calculated; 10 g/kg (as supplied liquid paint). EU Solvent Emissions Directive (Commission Directive 1999/13/EC). VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerance. |
|---|
Coating hazard GB 30981.2-W-Pb≤90-C; complies with GB 30981.2-2025
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
Newbuilding/refit: Intercryl 559 should always be applied over the recommended primer. The primer surface should be dry and free of contaminants, and Intercryl 559 must be applied within the specified recoat interval (refer to the relevant product data sheet). Damaged areas should be prepared to the specified standard (e.g. Sa 2.5 (ISO 8501-1:2007)) and primed before applying Intercryl 559.
All surfaces shall be washed with fresh water to remove all dirt and contamination.
Repair/in-service maintenance: repair areas with Intercryl 559 during in-service maintenance.
For specific advice, consult your local International Paint representative.
This coating is a single-component product; stir thoroughly with a power mixer before application.
Not recommended. Use water only in special cases (max 5% by volume).
Airless spray application is not recommended.
Applicable. Use suitable dedicated equipment. Thinning may be required.
Suitable.
Water
Flush all equipment thoroughly with water. Store unused paint in tightly closed containers. In partly filled containers, surface skinning and/or increased viscosity may occur after storage. Strain the paint before use.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; other regions — contact the regional office
Do not apply when the steel temperature is below 0 °C.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
In the Recoat Data section, unlimited = 'ext'. See the Marine Painting Guide — Definitions and Abbreviations available on our website.
| Packaging Specifications | Component A volume; packaging |
|---|---|
| 5 L | 5 L, 5 L. For other pack sizes, contact International Paint. |
| Packaging Specifications | Packaging weight |
|---|---|
| 5 L | 7.22 kg |
| Shelf life | At 25 °C, minimum 12 months. Thereafter, re-inspection is required. Store in a dry, sheltered place away from heat and sources of ignition. |
|---|
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
