Suitable for carrying more than 2000 cargoes, including refined and crude petroleum products, vegetable oils, animal oils, sodium hydroxide and ballast seawater. A high-solids, two-component, FDA-compliant epoxy cargo oil tank coating, resistant to a wide range of cargoes. Parameters on this page: volume solids 75% ± 2%, dry film thickness 125 µm, theoretical spreading rate 6 m²/L. Comparable products of the same brand: Interbond 201 - Low Temperature Epoxy Primer/Topcoat, Intercryl 559 Smooth Washable Topcoat, Intergard 7020 Abrasion-resistant Aluminium Pure Epoxy.
Data source: International original Technical Data Sheet (TDS), "Interline 704HS High-solids Tank Lining Coating"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 75% ± 2% |
|---|---|
| Dry Film Thickness | 125 µm |
| Theoretical Spreading Rate | 6 m²/L |
| VOC | 209 g/L (neat) (EPA Method 24) 171 g/kg(… |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B = 3:1 (by volume) |
| Colour / Appearance | THA710 pink, THA712 grey, THA711 white |
| Gloss | Matt |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A high-solids, two-component, FDA-compliant epoxy cargo oil tank coating, resistant to a wide range of cargoes.
Suitable for carrying more than 2000 cargoes, including refined and crude petroleum products, vegetable oils, animal oils, sodium hydroxide and ballast seawater.
For newbuilding or maintenance and repair.
| Colour | THA710 pink, THA712 grey, THA711 white |
|---|---|
| Topcoat/gloss | Matt |
| Component B (curing agent) | THA713 |
| Volume Solids | 75% ±2% (ISO 3233:1998) |
| Mixing ratio | Component A : Component B = 3:1 (by volume) |
| Standard film thickness | 125 µm dry film thickness (167 µm wet film thickness) |
| Theoretical Spreading Rate | Theoretical spreading rate 6 m²/L at 125 µm dry film thickness, allowing for a suitable loss factor |
| Application Methods | Airless spray, brush, roller |
| Flash Point | Component A 45 °C; Component B 42 °C; mixed 30 °C |
| Induction Time | 30 min at temperatures below 25 °C |
| Drying data | 5°C | 10°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 6 h | 3 h | 2 h | 1.5 h |
| Hard dry [ISO 9117-1:2009] | 21 h | 9.5 hours | 6 h | 3 h |
| Pot life after mixing | 4 h | 3 h | 1.5 h | 60 min |
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 5°C | 10°C | 25°C | 35°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Interline 704HS | 24 h | 35 days | 16 h | 35 days | 7 h | 35 days | 4 h | 35 days |
| Volatile Organic Compounds | 209 g/L (neat) (EPA Method 24) 171 g/kg (neat liquid paint). EU Solvent Emissions Directive (Commission Directive 1999/13/EC). VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|
Coating hazards GB 30981.2-S-Pb≤1000-NC; complies with GB 30981.2-2025
When used as part of an approved system, this product holds the following certificates: • Food contact - complies with US Food and Drug Administration regulations: liquid food and dry food. For details, consult your local International Paint representative.
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
Newbuilding/major repair: where required, remove weld spatter and grind welds and sharp edges smooth.
The product shall be applied only to surfaces abrasive-blast-cleaned to Sa2.5 (ISO 8501-1:2007).
A sharp, angular surface profile of 50–100 µm is recommended.
Narrow areas remaining after blast cleaning (consult International Paint) that have not reached the specified standard can be power tool cleaned to Pt 3 (JSRA SPSS:1984).
Interline 704HS must be applied before the steel oxidises. If oxidation has occurred, the entire oxidized area should be re-blasted to the specified standard.
Surface defects exposed during blasting must be ground, welded or treated by a suitable method.
Or use dehumidification to maintain the blasting standard.
For maintenance, consult International Paint.
For specific advice, consult your local International Paint representative.
Note: for marine environments in North America, the following surface preparation standards may be used: SSPC-SP10 in place of Sa2.5 (ISO 8501-1:2007), SSPC-SP11 in place of Pt3 (JSRA SPSS:1984).
The coating is supplied in two containers as one unit. Always mix the entire unit in the supplied ratio.
(1) Stir the base (Component A) with a power mixer.
(2) Mix all of the curing agent (Component B) with the base (Component A) and stir thoroughly with a power mixer.
International GTA220. Normally no thinning is required. Under extreme conditions, consult your local representative for application advice. Do not thin beyond the limits of local environmental regulations.
Recommended nozzle size 0.64–0.69 mm (25–27 thou); total output fluid pressure at the nozzle not less than 211 kg/cm² (3000 lb/in²).
Conventional spray application is not recommended.
Brush application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Roller application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Do not leave paint in hoses, spray guns or spray equipment. Flush all equipment thoroughly with International thinner. Once mixed, paint should not be resealed; if work is interrupted for too long, mix a fresh batch before resuming application.
All equipment should be cleaned immediately after use with International thinner. Flushing spray equipment periodically during the day is good working practice. Cleaning frequency depends on the volume sprayed, temperature and time in use (including delays). Do not exceed the pot life of the paint.
All surplus paint and empty containers must be disposed of in accordance with appropriate local regulations/laws.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; China — tel. (86) 532 83889090; other regions — contact the regional office.
This product does not cure adequately below 5 °C.
Consult International Paint to determine whether Interline 704HS is suitable for the cargo to be carried.
Drying times and overcoating intervals may vary with site factors such as tank geometry or ventilation rate. For the required interval between completion of coating and cargo loading, refer to the detailed application procedure.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
| Packaging Specifications | Component A | Component B | ||
| Volume | Packaging | Volume | Packaging | |
| 20 L | 15 L | 20 L | 5 L | |
For other packaging sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 20 L | 31.65 kg |
| Shelf life | 18 months at 25 °C. Thereafter, re-inspection is required. Store in a dry, sheltered place away from heat and sources of ignition. |
|---|
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
