6429 EVAMAX 2000 High-solids Epoxy is an epoxy coating. EVAMAX 2000 is a mixed coating formulated from epoxy resin, special abrasion-resistant raw materials and polyamide resin. Parameters on this page: volume solids 78 ± 2%, dry film thickness 100–250 µm, theoretical spreading rate 0.128–0.321 L/m². Comparable products from the same brand: 5006 ALP 500 Epoxy, 5055 BANNOH 500 Epoxy, 5055D BANNOH 500 AC Epoxy.
Source: CMP original technical data sheet (TDS) "6429 EVAMAX 2000 High-solids Epoxy"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 78 ± 2% |
|---|---|
| Dry Film Thickness | 100–250 µm |
| Theoretical Spreading Rate | 0.128-0.321 L/m2 |
| VOC | 258 g/L |
| Density / Specific Gravity | 1.56 g/ml |
| Number of Components | Two-component |
| Thinner | EPOXY THINNER A |
| Mixing Ratio | Base : curing agent = 75:25 (by volume) |
| Colour / Appearance | Grey, red-brown |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
EVAMAX 2000 is a mixed coating formulated from epoxy resin, special abrasion-resistant raw materials and polyamide resin. It has excellent characteristics such as strong adhesion, good flexibility, impact resistance, abrasion resistance, scratch resistance and rust protection.
The coating is suitable for spraying on exterior decks and holds.
| Type | High-Solids Epoxy |
|---|---|
| Use | For cargo holds |
| Mixing Ratio | Base : curing agent = 75:25 (by volume) |
|---|---|
| Colour | Grey, red-brown |
| Flash Point | Base 37 °C; curing agent 21.5 °C |
| Density | 1.56 g/ml |
| Volume Solids | 78 ± 2% |
| Volatile organic compound content | 258 g/L |
| Theoretical spreading rate | 0.128-0.321 L/m2 |
| Thickness | WFT 128–321 µm |
| Dry film | 100–250 µm |
(dry film 200 µm)
| Temperature | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 10 h | 5 h | 3 h |
| Hard Dry | 22 h | 14 h | 10 h | |
| Recoat interval | At least | 22 h | 14 h | 10 h |
| At most | 15 days | 10 days | 7 days | |
| Pot life | 5 h | 2.5 h | 1.5 h | |
| Application method | Airless spray, brush, roller |
|---|---|
| Weather: temperature | Minimum 10 °C |
| Humidity | Maximum 85% RH |
| Airless spray: viscosity | 1.5-2.0Pa.s |
| Nozzle | Graco419-623 |
| Paint output pressure | 15-25 Mpa |
| Spray gun speed | 60–80 cm/s |
| Thinner | EPOXY THINNER A |
| Thinning | 0–15% by volume |
| Newbuilding | Follow the shipyard standards. Consult your CMP representative for advice. |
|---|---|
| Repair and maintenance | Remove oil and grease. Remove salts and other contaminants with high-pressure clean water, then dry |
| Fully. Remove damaged areas by abrasive blasting to at least Sa 2 (ISO 8507-1 | 2007) or with power tools |
| power tools to St 3 (ISO 8507-1 | 2007). |
| Rinse with water | Consult your CMP representative for advice. |
The type and degree depend on the actual condition of the material and the required performance.
Use standards consistent with the Worldwide Marine Specifications.
| Preceding coat | CERABOND 2000, NZ PRIMER S |
|---|---|
| Subsequent coat | - |
| Packaging | Two-component |
Note: 1. In confined spaces or restricted spaces at low temperature, ventilation is necessary to remove volatilised solvent and promote film formation during application and drying.
2. Stir the base with a mixer until homogeneous, then add the curing agent and mix with a power mixer. Then add the appropriate amount of thinner and mix.
3. Excessive thinner reduces sag resistance and film performance.
4. If the film surface is likely to be exposed directly to sunlight, the next coat shall be applied within the minimum time interval where possible.
5. This product is not suitable for FDA (dry foodstuff) applications.
6. Waiting time before first cargo loading
| Temperature | 10°C | 20°C | 30°C |
| 200 µm (days) | 20 | 12 | 7 |
| 400 µm (days) | 30 | 18 | 11 |
7. When the average ambient temperature is below 15 °C, the use of "EVAMAX 2000 QD" is recommended.
8. The powder in the product settles easily. Normally, stirring restores the same performance as the original product.
9. VOC content and density are theoretical calculated values based on a representative colour formulation (grey) without thinner. Values vary between colour formulations.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
