6081A CMP NOVA 2000 QD Tar-free Modified High-solids Epoxy is an epoxy coating. It has excellent bonding, film toughness and abrasion resistance, among other physical properties, as well as excellent resistance to pure water, seawater and oil. Parameters on this page: volume solids 80 ± 2% (ISO: 3233), dry film thickness 125–250 µm, theoretical spreading rate 0.156–0.312 L/m². Comparable products from the same brand: 5006 ALP 500 Epoxy, 5055 BANNOH 500 Epoxy, 5055D BANNOH 500 AC Epoxy.
Source: CMP original technical data sheet (TDS) "6081A CMP NOVA 2000 QD Tar-free Modified High-solids Epoxy"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 80 ± 2% (ISO:3233) |
|---|---|
| Dry Film Thickness | 125–250 µm |
| Theoretical Spreading Rate | 0.156-0.312 L/m2 |
| VOC | 249 g/L (Method24) |
| Density / Specific Gravity | 1.43 g/ml (ISO:2811) |
| Number of Components | Two-component |
| Thinner | EPOXY THINNER A |
| Mixing Ratio | Base : curing agent = 83:17 (by volume) |
| Colour / Appearance | Light grey, cream yellow, red-brown, grey |
CMP NOVA 2000 QD is a high-solids tar-free modified epoxy based on modified epoxy resin and pigments. It has excellent bonding, film toughness and abrasion resistance, among other physical properties, as well as excellent resistance to pure water, seawater and oil.
This product is an IMO PSPC-certified WBT coating, suitable for many parts of the hull. Excellent curing performance at low temperatures.
| Type | Tar-free Modified High-solids Epoxy |
|---|---|
| Use | Can be used for ballast tanks, void spaces, etc. |
| Mixing Ratio | Base : curing agent = 83:17 (by volume) |
|---|---|
| Colour | Light grey, cream yellow, red-brown, grey |
| Flash Point | Base 37 °C; curing agent 21.5 °C |
| Density | 1.43 g/ml (ISO:2811) |
| Volume Solids | 80 ± 2% (ISO:3233) |
| Volatile organic compound content | 249 g/L (Method24) |
| Theoretical spreading rate | 0.156-0.312 L/m2 |
| Thickness | Wet film 156–313 µm |
| Dry film | 125–250 µm |
(dry film 250 µm)
| Temperature | -5 °C | 0 °C | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 17 h | 11.5 h | 7 h | 3.5 h | 1.5 h | 30 min |
| Hard Dry | 44 h | 34 h | 22 h | 15.5 h | 6 h | 3 h | |
| Recoat interval | At least | 44 h | 34 h | 22 h | 15.5 h | 6 h | 3 h |
| At most* | 15 days | 15 days | 10 days | 7 days | 4 days | ||
| Pot life | 12 h | 8 h | 5 h | 3 h | 2 h | 1 h | |
| Minimum launching time | 15 days | 10 days | 6 days | 4 days | 2 days | ||
| Application method | Airless spray, brush, roller |
|---|---|
| Weather: temperature | -5 - 30°C |
| Humidity | Maximum 85% RH; steel temperature at least 3 °C above the dew point |
| Airless spray: viscosity | 1.5-2.0Pa.s |
| Nozzle | Graco519-723 |
| Paint output pressure | 15-25 Mpa |
| Spray gun speed | 60–80 cm/s |
| Thinner | EPOXY THINNER A |
| Thinning | 0–20% by volume |
| Preceding coat | CERBOND 2000, EPICON ZINC RICH PRIMER B-2 |
| Subsequent coat | - |
| Packaging | Two-component |
Note: 1. In enclosed spaces or confined spaces at low temperature, ventilation is necessary to remove volatilised solvent during application and film formation to promote film formation. Note that curing time is extended at low temperatures, especially below 10 °C.
2. Stir the base with a mixer until homogeneous, then add the curing agent and mix with a power mixer. Then add the appropriate amount of thinner and mix.
3. Excessive solvent may reduce sag resistance.
4. Application is possible down to -5 °C, but hard dry takes a long time, and full cure is achieved only as the temperature rises.
5. *If the film surface is likely to be exposed directly to sunlight, the next coat shall be applied within the minimum time interval where possible.
6. When used in tanks, if some locations (e.g. edges) cannot achieve sufficient film thickness, stripe coating is recommended.
7. Refer to the product safety data sheet before use.
8. When using plural-component spray equipment, the mixing ratio of base and curing agent must be confirmed by CMP.
9. VOC content and density are theoretical calculated values excluding thinner. Values vary with colour, production process and local regulations.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
