6081 CMP NOVA 2000 Tar-free Modified High-solids Epoxy Coating belongs to Epoxy. It exhibits physical properties including excellent adhesion, film toughness and abrasion resistance, as well as excellent resistance to pure water, seawater and oil. Parameters on this page: volume solids 80 ± 2% (ISO:3233), dry film thickness 125–250 µm, theoretical spreading rate 0.156–0.313 L/m². Comparable models from the same brand: 5006 ALP 500 Epoxy Coating, 5055 BANNOH 500 Epoxy Coating, 5055D BANNOH 500 AC Epoxy Coating.
Parameter source: CMP original Technical Data Sheet (TDS) \"6081 CMP NOVA 2000 Tar-free Modified High-solids Epoxy Coating\"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 80 ± 2% (ISO:3233) |
|---|---|
| Dry Film Thickness | 125–250 µm |
| Theoretical Spreading Rate | 0.156-0.313 L/m2 |
| VOC | 256 g/L (Method24) |
| Density / Specific Gravity | 1.43 g/ml (ISO:2811) |
| Number of Components | Two-component |
| Thinner | EPOXY THINNER A, EPOXY THINNER B |
| Mixing Ratio | Base : curing agent = 83:17 (by volume) |
| Colour / Appearance | Light grey, cream yellow, red-brown, grey |
CMP NOVA 2000 is a high-solids tar-free modified epoxy coating based on modified epoxy resin and pigments. It exhibits physical properties including excellent adhesion, film toughness and abrasion resistance, as well as excellent resistance to pure water, seawater and oil.
This product is an IMO PSPC-certified WBT coating and is suitable for numerous areas of the hull.
| Type | Tar-free Modified High-solids Epoxy |
|---|---|
| Use | Used for ballast water tanks, crude oil tanks, void spaces, hatch covers, fire hydrants, bridges, bridge piers, sheet piling, port facilities and other applications. |
| Mixing Ratio | Base : curing agent = 83:17 (by volume) |
|---|---|
| Colour | Light grey, cream yellow, red-brown, grey |
| Flash Point | Base 37 °C; curing agent 21.5 °C |
| Density | 1.43 g/ml (ISO:2811) |
| Volume Solids | 80 ± 2% (ISO:3233) |
| Volatile organic compound content | 256 g/L (Method24) |
| Theoretical spreading rate | 0.156-0.313 L/m2 |
| Thickness | Wet film 156–313 µm |
| Dry film | 125–250 µm |
(dry film 250 µm)
| Temperature | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 11 h | 5 h | 3.5 h |
| Hard Dry | 22 h | 13.5 h | 10.5 h | |
| Recoat interval | At least | 22 h | 13.5 h | 10.5 h |
| At most* | 15 days | 10 days | 7 days | |
| Pot life | 5 h | 3 h | 2 h | |
| Minimum launching time | 8 days | 6 days | 4 days | |
| Application method | Airless spray, brush, roller |
|---|---|
| Weather: temperature | 10 - 40°C |
| Humidity | Maximum 85% RH; steel temperature at least 3 °C above the dew point |
| Airless spray: viscosity | 1.5-2.0Pa.s |
| Nozzle | Graco519-723 |
| Paint output pressure | 15-25 Mpa |
| Spray gun speed | 60–80 cm/s |
| Thinner | EPOXY THINNER A, EPOXY THINNER B |
| Thinning | 0–15% by volume |
| Preceding coat | CERBOND 2000, EPICON ZINC RICH PRIMER B-2 |
| Subsequent coat | - |
| Packaging | Two-component |
Note: 1. In confined spaces or restricted spaces at low temperature, ventilation is necessary to remove volatilised solvent and promote film formation during application and drying.
2. Stir the base with a mixer until homogeneous, then add the curing agent and mix with a power mixer. Then add the appropriate amount of thinner and mix.
3 Excess thinner may reduce sag resistance and film performance.
4 When used in tanks, if sufficient film thickness is difficult to achieve in some areas (e.g. edges), touch-up is recommended.
5. *If the film surface is likely to be exposed directly to sunlight, the next coat shall be applied within the minimum time interval where possible.
6 VOC content and density are theoretical calculated values under thinner-free conditions. Values vary with colour, production process and local regulations.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
