6060 PERMAX NO.3300 Epoxy Glass Flake High-build Paint belongs to glass flake paints, epoxy system. PERMAX NO.3300 consists mainly of glass flake epoxy resin; it offers excellent physical properties such as adhesion, roughness and abrasion resistance, together with chemical resistance to salt water, pure water, crude oil, alkalis and weak acids. Parameters on this page: volume solids 80 ± 2%, DFT 200-300 µm, theoretical spreading rate 0.25-0.375 L/m2. Comparable models from the same brand: 1050 NZ PRIMER S Zinc-free Epoxy Shop Primer, 200 GALVANITE No.200 PRIMER Epoxy Primer for Galvanized Steel, 2419K ECO SWAN Water-borne Epoxy Ester Paint.
Parameter source: original CMP technical data sheet (TDS) "6060 PERMAX NO.3300 Epoxy Glass Flake High-build Paint"; values such as spreading rate are converted from TDS parameters and serve as selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 80 ± 2% |
|---|---|
| Dry Film Thickness | 200–300 µm |
| Theoretical Spreading Rate | 0.25-0.375 L/m2 |
| VOC | 241 g/L |
| Density / Specific Gravity | 1.46 g/mL |
| Number of Components | Two-component |
| Thinner | EPOXY THINNER A |
| Mixing Ratio | Base : curing agent = 77:23 (by volume) |
| Colour / Appearance | Light grey, red-brown |
PERMAX NO.3300 consists mainly of glass flake epoxy resin; it offers excellent physical properties such as adhesion, roughness and abrasion resistance, together with chemical resistance to salt water, pure water, crude oil, alkalis and weak acids. It is suitable for cargo holds, splash zones and underwater areas.
| Type | Epoxy Glass Flake High-build Paint |
|---|---|
| Use | Suitable for splash zones and underwater areas of ship hulls and superstructures |
| Mixing Ratio | Base : curing agent = 77:23 (by volume) |
|---|---|
| Colour | Light grey, red-brown |
| Flash Point | Base 32°C Hardener 28°C |
| Density | 1.46 g/mL |
| Volume Solids | 80 ± 2% |
| Volatile organic compound content | 241 g/L |
| Theoretical spreading rate | 0.25-0.375 L/m2 |
| Thickness | WFT 250-375 µm DFT 200-300 µm |
(dry film 250 µm)
| Temperature | -5 °C | 0 °C | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 15 h | 10 h | 7 h | 4 h | 2.5 h | 1.5 h |
| Hard Dry | 60 h | 36 h | 24 h | 13 h | 7 h | 5 h | |
| Recoat interval | At least | 60 h | 36 h | 24 h | 13 h | 7 h | 5 h |
| At most | * | * | * | ||||
| Pot life | 15 h | 11 h | 8 h | 5 h | 3 h | 2 h | |
| Application method | Airless spray, brush |
|---|---|
| Weather: temperature | Minimum -5 °C |
| Humidity | Maximum 85% RH; steel temperature at least 3 °C above the dew point |
| Airless spray: nozzle | Graco Balltip No205-732ZINCGUN(208-663) |
| Paint output pressure | 14.7-19.7 Mpa |
| Spray gun speed | 60–80 cm/s |
| Thinner | EPOXY THINNER A |
| Thinning | 0-6% by volume |
| Preceding coat | - |
| Subsequent coat | BANNOH 500, BANNOH 500 N, EPICON FINISH HB |
| Packaging | Two-component |
1 Refer to the paint scheme data sheet.
2. In confined spaces or restricted spaces at low temperature, ventilation is necessary to remove volatilised solvent and promote film formation during application and drying.
3. Stir the base with a stirrer until uniform, then add the curing agent and mix with the base using a powerful stirrer. Then add an appropriate amount of thinner and mix.
4 Excess thinner reduces sag resistance and film performance.
5 Equipment may require prior arrangement. For example, only the suction filter is sometimes fitted externally while no gun filter is fitted. Hose length, pump height and spray gun shall also be considered.
6 Density and volatile organic content are theoretically calculated from a representative formulation (light grey) without thinner. Values vary with colour, production process and local regulations.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
