200 GALVANITE No.200 PRIMER Epoxy Zinc-coated Steel Primer belongs to Epoxy and is used as a primer. GALVANITE No.200 PRIMER is a primer for coating galvanized steel, composed of epoxy resin and polyamide resin with special anti-corrosive pigments. Parameters on this page: Volume Solids 47 ± 1% (ISO: 3233), Dry Film Thickness 30–50 µm, Theoretical Spreading Rate 0.064–0.106 L/m². Comparable models from the same brand and category: 1050 NZ PRIMER S Zinc-free Epoxy Shop Primer, 400 GALVANITE No.400 PRIMER Epoxy Polyamide Resin Primer, 5106D EPICON PRIMER HB Epoxy Primer.
Parameter source: CMP original Technical Data Sheet (TDS) “200 GALVANITE No.200 PRIMER Epoxy Zinc-coated Steel Primer”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 47 ± 1% (ISO: 3233) |
|---|---|
| Dry Film Thickness | 30–50 µm |
| Theoretical Spreading Rate | 0.064-0.106 L/m2 |
| VOC | 530 g/L (Method 24) |
| Density / Specific Gravity | 1.38 g/mL (ISO: 2811) |
| Number of Components | Two-component |
| Thinner | EPOXY THINNER G |
| Mixing Ratio | Base : curing agent = 84:16 (by volume) |
| Colour / Appearance | White |
GALVANITE No.200 PRIMER is a primer for coating galvanized steel, composed of epoxy resin and polyamide resin with special anti-corrosive pigments.
| It has the following advantages | 1. Excellent adhesion to galvanized surfaces 2. Excellent water resistance 3. Fast drying 4. Good compatibility with various coatings |
|---|
| Type | Epoxy Zinc-coated Steel Primer |
|---|---|
| Use | May be used as a primer for galvanized steel |
| Mixing Ratio | Base : curing agent = 84:16 (by volume) |
|---|---|
| Colour | White |
| Flash Point | Base 17.5 °C Hardener 19.5 °C |
| Density | 1.38 g/mL (ISO: 2811) |
| Volume Solids | 47 ± 1% (ISO: 3233) |
| Volatile organic compound content | 530 g/L (Method 24) |
| Theoretical spreading rate | 0.064-0.106 L/m2 |
| Wet Film Thickness | 64–106 µm |
| Dry Film Thickness | 30–50 µm |
(dry film 40 µm)
| Temperature | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 30 min | 20 min | 10 min | 5 min |
| Hard Dry | 8 h | 6 h | 4 h | 3 h | |
| Recoat interval | At least | 18 h | 10 h | 4 h | 3 h |
| At most | 90 days | 60 days | 30 days | ||
| Pot life | 36 h | 30 h | 24 h | 12 h |
| Application method | Airless spray, brush |
|---|---|
| Weather: temperature | Minimum 5 °C |
| Humidity | Maximum 85% |
| Airless spray: viscosity | 55–65 s (Ford Cup #4) |
| Nozzle | Graco 619,719 |
| Paint output pressure | 10.8-13.7 Mpa |
| Spray gun speed | 80–100 cm/s |
| Thinner | EPOXY THINNER G |
| Thinning | 0–7% by volume |
Remove white rust or other contaminants with a wire brush or sandpaper; the surface to be coated must then be clean. Remove dust, oil and other contaminants with a power brush, degreaser or solvent.
| Preceding coat | - |
|---|---|
| Subsequent coat | EVAMARINE, SWAN HB L, EPICON FINISH HB, ACRI 700 FINISH ST and other products |
| Packaging | Two-component |
Note: 1. In enclosed spaces or confined spaces under low-temperature conditions, ventilation equipment is necessary to remove volatilized solvent during application and film formation and to promote paint film formation.
2. Stir the base with an electric stirrer to a uniform state, then thoroughly stir all of the curing agent with the base. Finally add an appropriate amount of thinner and mix thoroughly.
3. Excessive solvent may reduce sag resistance and other film properties.
4. Application is possible down to -5 °C, but hard dry takes a long time, and full cure is achieved only as the temperature rises.
5. Density, volume solids and VOC content are theoretical calculated values without thinner.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
