Waterborne Acrylic Sealer ZDW1030 is a waterborne coating used as a primer. Used for surface treatment of cement or concrete substrates before applying high-performance concrete coatings, providing a surface with anti-penetration, easy cleaning and good adhesion for subsequent coats. A one-component waterborne eco-friendly sealer composed of waterborne acrylic emulsion, water, additives, etc. Parameters on this page: volume solids 30 ± 3%, dry film thickness 25/40/50 µm, theoretical spreading rate 0.166 kg/m². Comparable products from the same brand: ZDW6500 Waterborne Epoxy Primer, Waterborne Acrylic Intermediate Coat ZDW2050, Waterborne Acrylic Topcoat ZD5100.
Source: ZINDN original technical data sheet (TDS) "Waterborne Acrylic Sealer ZDW1030"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 30 ± 3% |
|---|---|
| Dry Film Thickness | 25/40/50 µm |
| Theoretical Spreading Rate | 0.166 kg/m² |
| VOC | ≤50g/L |
| Density / Specific Gravity | 1.0 ± 0.1 |
| Number of Components | One-component |
| Flash Point | >115°C |
| Colour / Appearance | Clear |
| Gloss | Flat |
ZDW1030 Waterborne Acrylic Sealer
A one-component waterborne eco-friendly sealer composed of waterborne acrylic emulsion, water, additives, etc.
Excellent penetration ensures good adhesion between ZINDN series products and the substrate surfaces of most concrete, cement and masonry structures; after treatment, the substrate gains improved sealing and adhesion strength of the composite coating to the substrate.
Ultra-low VOC content, eco-friendly.
For preparing cement or concrete substrates before applying high-performance concrete coatings, providing a surface with anti-penetration, easy cleaning and good adhesion for the subsequent coat.
| Colour | Clear |
|---|---|
| Gloss | Flat |
| Volume Solids | 30±3% |
| Mixed density (kg/L) | 1.0±0.1 |
| Dry film thickness (µm) | Minimum 25 | Typical 40 | Maximum 50 |
| Wet film thickness (µm) | 83 | 133 | 167 |
| Theoretical spreading rate (kg/m²) | 0.083 | 0.133 | 0.166 |
Note: as a penetrating sealer, the final dry film thickness depends on the porosity and penetration of the substrate.
| Practical Spreading Rate | Allowing for a loss factor, the substrate porosity and surface roughness affect the practical spreading rate. |
|---|---|
| VOC content | ≤50g/L |
New concrete substrates shall have been completed for at least 20 days; all substrates shall be free from dirt, and all cracks, joints, protrusions and depressions shall be properly treated before applying this product.
Before application, treat the concrete surface using dust-free blasting equipment, rotary grinding tools, blasting or high-pressure water jetting to achieve a suitable surface roughness and remove contaminants, and vacuum up the dust, keeping the substrate clean and free of standing water.
The substrate temperature must not be below 5 °C and shall be at least 3 °C above the air dew point; relative humidity ≤ 80%. Temperature and relative humidity shall be measured on the substrate near the working area.
Do not apply outdoors in adverse weather such as rain, fog, snow, strong wind and heavy dust;
| Mixing | This product is supplied as a one-component pack. Ready to use on opening; no thinning required. |
|---|---|
| Cleaning solvent | Water (clean tools before the paint is touch dry; once touch dry, a glycol ether solvent may be used for tool cleaning) |
| Application Methods | Air spray, brush or roller is recommended; airless spray may also be used. |
|---|
| Application Methods | Unit | High-pressure airless spray | Air Spray | Brush/roller |
| Spray gun tip size | mm | 0.38~0.45 | 1.5-1.8 | —— |
| Spray pressure | kg/cm² | 150~200 | 3-4 | —— |
| Thinning quantity | % | 0 | 0 |
| Substrate surface temperature | 5°C | 15°C | 25°C | 35°C |
| Touch Dry | 2 h | 1 h | 0.5 h | 20 min |
| Hard Dry | 4 h | 2 h | 1 h | 30 min |
| Minimum recoat interval | 4 h | 2 h | 1 h | 30 min |
| Maximum recoat interval | Unlimited, provided the surface is clean and free of contaminants |
Note: the above data are measured under well-ventilated conditions, at typical film thickness and 65% relative humidity, and are for reference only.
Actual drying times and the interval before recoating may be longer or shorter depending on film thickness, ventilation, humidity, the underlying paint, requirements for early handling and mechanical strength, and other factors.
| Preceding coat | None |
|---|---|
| Subsequent coat | Waterborne acrylic intermediate coat, waterborne acrylic topcoat |
If the substrate is heavily porous, apply several coats to fully seal the surface and avoid bubbles and pinholes when applying the next coat.
| Packaging Specifications | 19kg |
|---|---|
| Flash Point | >115°C |
| Storage conditions | Store in accordance with national regulations. Keep at a temperature above 0 °C in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. |
| Shelf life | Shelf life is 1 year under good storage conditions. |
Site safety must comply with the relevant national or local regulations. Read the safety labels on the packaging and the product Safety Data Sheet (MSDS).
Avoid inhaling spray mist, avoid contact of paint with skin and eyes, and do not swallow the product. Take the necessary precautions and protective measures to protect the environment. Use only in well-ventilated conditions. In confined or poorly ventilated areas, provide forced ventilation.
Waste disposal must comply with the relevant national or local regulations.
The information and data in this document are accumulated from our tests and practical experience and may serve as an application guide. Since the use of the product is generally beyond our control, we guarantee only the quality of the product itself. We reserve the right to modify this document without prior notice as the product is improved.
| Version information | Published in June 2022; this data sheet supersedes all previous versions |
|---|
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
