ZD6310 Epoxy Oil-resistant Static-conductive Topcoat is an epoxy coating used as a topcoat. It provides antistatic and anticorrosive protection for cargo holds and storage tanks carrying crude oil, gasoline, aviation gasoline, kerosene, naphtha and benzene, and may also be used in other locations requiring static conductivity. A two-component anticorrosive coating based on epoxy resin and epoxy hardener, with non-carbon composite conductive filler, anti-corrosive pigments and additives. Parameters on this page: volume solids 85% ± 2%, dry film thickness 100 µm, theoretical spreading rate 260 g/m². Comparable products of the same brand and type: ZD6310-N01F Epoxy Oil-resistant Static-conductive Topcoat, ZD6095 Solvent-free Epoxy Topcoat, ZD6510 Epoxy Topcoat.
Parameter source: ZINDN manufacturer's Technical Data Sheet (TDS) "ZD6310 Epoxy Oil-resistant Static-conductive Topcoat"; spreading rate and other values are converted from TDS parameters and are for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 85% ± 2% |
|---|---|
| Dry Film Thickness | 100µm |
| Theoretical Spreading Rate | 260 g/m² |
| VOC | — |
| Density / Specific Gravity | 1.8 ± 0.1 |
| Number of Components | Two-component |
| Flash Point | >25 °C (components A, B and the mixture) |
| Thinner | X-500 Epoxy Thinner |
| Mixing Ratio | Component A (base) : Component B (curing agent) = 30:2 |
ZD6310 Epoxy Oil-resistant Static-conductive Topcoat
A two-component anticorrosive coating based on epoxy resin and epoxy hardener, with non-carbon composite conductive filler, anti-corrosive pigments and additives
High adhesion, flexibility and impact resistance;
Excellent oil resistance and corrosion resistance; no dissolution or swelling after use;
Excellent antistatic performance; coating resistivity 10^8–10^11 Ω.
For antistatic, anticorrosive protection of tanks and storage vessels carrying crude oil, gasoline, aviation gasoline, kerosene, naphtha and benzene; also suitable for other applications requiring static dissipation.
| Colour | White |
|---|---|
| Solids content by mass | 85%±2% |
| Volume Solids | 73%±2% |
| Mixed density (kg/L) | 1.8±0.1 |
| Typical film thickness and theoretical spreading rate | 260g/m² |
| Wet Film Thickness | 145µm |
| Dry Film Thickness | 100µm |
Remove all oil, grease and contaminants from the surface with a suitable cleaner; keep the surface clean, dry and free of contamination.
Apply only over the recommended epoxy oil-resistant static-conductive primer and within the specified recoat interval. Damaged areas of the primer must be abrasive blast cleaned to Sa2.5 (ISO8501-1) or power tool cleaned to St3, and these areas
Application environment temperature 5–38 °C, relative humidity not more than 85%, and the steel surface temperature should be at least 3 °C above the dew point. Do not apply outdoors in adverse weather such as rain, fog, snow, strong wind and heavy dust.
| Mixing | This product is supplied as two containers forming one unit. Stir the base thoroughly with a power mixer, add the curing agent in the specified ratio, stir again with a power mixer, and add the recommended thinner to adjust to a suitable application viscosity. Once mixed, use within the specified pot life. |
|---|---|
| Thinner / Cleaning Solvent | X-500 Epoxy Thinner |
| Mixing ratio (by weight) | Component A (base) : Component B (curing agent) = 30:2 |
| Induction Time | 30 min (25 °C) |
| 5°C | 15°C | 25°C | 35°C |
| 5.5 h | 5 h | 4 h | 3 h |
| Application Methods | Airless spray and air spray are recommended; brush and roller are recommended only for touch-up, small-area application or repair. |
|---|
| Application Methods | Unit | High-pressure airless spray | Air Spray | Brush/roller |
| Spray gun tip size | mm | 0.43~0.58 | 1.5~2.5 | —— |
| Spray pressure | kg/cm² | 150~200 | 3~4 | —— |
| Thinning quantity | % | 0~10 | 10~20 | 5~10 |
| Substrate surface temperature | 5°C | 15°C | 25°C | 35°C |
| Touch Dry | 4 h | 2 h | 1 h | 30 min |
| Hard Dry | 24 h | 16 h | 12 h | 8 h |
| Minimum recoat interval | 24 h | 16 h | 12 h | 8 h |
| Maximum recoat interval | Unlimited, but any chalk layer from long-term exposure must be removed completely before recoating. |
|---|
Note: the above data are measured under well-ventilated conditions, at typical film thickness and 75% relative humidity, and are for reference only.
Actual drying time and the interval before recoating may be longer or shorter, depending on film thickness, ventilation, humidity, the previous coat,
| Preceding coat | Epoxy Oil-resistant Static-conductive Primer |
|---|
| Packaging Specifications | Component A 30 kg, Component B 2 kg |
|---|---|
| Flash Point | >25 °C (components A, B and the mixture) |
| Storage conditions | Store in accordance with national regulations. Keep in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. |
| Shelf life | Shelf life is 1 year under good storage conditions. |
This product contains flammable materials; site safety must comply with the relevant national or local regulations. Read the safety labels on the packaging and the product Safety Data Sheet (MSDS).
Avoid inhaling solvent vapours and spray mist, avoid contact of paint with skin and eyes, and do not swallow the product. Take the necessary precautions and protective measures for fire prevention, explosion prevention and environmental protection. Use only in well-ventilated conditions. In confined or poorly ventilated areas, provide forced ventilation.
Waste disposal must comply with the relevant national or local regulations.
The information and data in this document are accumulated from our tests and practical experience and may serve as an application guide. Since the use of the product is generally beyond our control, we guarantee only the quality of the product itself. We reserve the right to modify this document without prior notice as the product is improved.
| Version information | Published in September 2023; this data sheet supersedes all previous versions |
|---|
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
