SIGMARINE 49 Alkyd Enamel 49

Browse Similar Models by CategoryThis model belongs to: Topcoat, Alkyd

Key properties

• Suitable for both interior and exterior surfaces
• Excellent levelling, easy to apply by brush
• Good weathering performance
• High hiding power
• Good colour retention
• Resistance to polluted gases: coating does not discolour on contact with sulphur dioxide gas
• Not suitable for underwater immersion or splash zones permanently in a wet condition
• May be overcoated on most intact alkyd coatings

Colour and gloss

• White (other colours customised to requirements)
• Gloss

Basic data at 20 °C (68 °F)

Product parameters

Maximum 407.0 g/L (approx. 3.4 lb/gal) (theoretical calculated value)

Recommended substrate condition and temperature

Substrate condition

• The compatible previous coat must be clean, dry and free of all contaminants.
• Before recoating an existing coating, roughen the surface sufficiently if necessary.

Substrate temperature and application conditions

• During application, the substrate temperature must not exceed 50 °C (122 °F)
• During application, the substrate surface temperature must be maintained at least 3 °C (5 °F) above the dew point.

Coating system specification

• Coating system for superstructures and deck outfitting — system sheet SYSTEM SHEET 3104
• Coating system for internal surfaces — system sheet SYSTEM SHEET 3105

Instructions for use

• Stir thoroughly before use
• Before application, raise the temperature of the components or the mixed paint to above 15 °C (59 °F); otherwise, thinner may need to be added to bring the paint viscosity

adjust to a state suitable for application.

• Excessive thinning generally reduces the sag resistance of the wet film
• During application and curing, ensure continuous, adequate ventilation (see sheets {1433} and {1434})

Air spray

Airless spray (single-feed pump)

Nozzle tip size

Approx. 0.48 mm (0.019 in)

Brush/roller

Safety Precautions

• For the coating and its recommended thinners, see Safety Sheets 1430 and 1431 and the relevant Material Safety Data Sheet
• This is a solvent-borne coating. Avoid inhaling spray mist and solvent vapours, and avoid contact of uncured paint with skin and eyes.

Worldwide

Although PPG Protective and Marine Coatings is committed to providing completely consistent products to users worldwide, from time to time it may be necessary to make minor adjustments to specific products to comply with local/national regulations or environmental requirements. In the following cases, use the corresponding alternative version of the product data sheet instead.

Reference information

• For the conversion table, refer to Information Sheet 1410
• For product data, refer to Information Sheet 1411
• For safety guidance, refer to Information Sheet 1430
• Safety and health in confined spaces | explosion hazard — toxic hazard: refer to Information Sheet 1431
• For safe working in confined spaces, refer to Information Sheet 1433
• For ventilation guidance, refer to Information Sheet 1434
• For relative humidity, substrate temperature and air temperature, refer to Information Sheet 1650

Quality guarantee

PPG warrants (1) that it has good title to the product, (2) that the product quality conforms to the relevant technical quality specifications in force at the date of manufacture of the product, and (3) that the supplied product is free of lawful claims by third parties for infringement of US patent rights. The above warranties are limited to those given by PPG and other express or implied warranties required by applicable laws and regulations for transactions and commercial practice; any abuse contrary to the stated conditions, and any other warranty for special purposes or uses, are excluded, and PPG shall be free from liability. To claim under this warranty, the buyer must notify PPG in writing within five (5) days of discovering the quality defect, and the date must be within the product's valid storage period or within one (1) year from delivery of the product to the buyer.

If the buyer fails to notify PPG of the defect as required above, this will prejudice the buyer's right to obtain compensation under this warranty from PPG!

Limitation of liability

In all cases, PPG shall not be liable for any indirect, special, incidental or consequential loss of any kind arising from or in connection with the use of this product (whether based on negligence, strict liability or tort).

The information in this product data sheet is based on laboratory tests we believe to be reliable, and is provided for guidance only. PPG may revise this information at any time as experience accumulates and product development progresses.

All recommendations and advice concerning the use of this product, whether in technical documents, in response to an enquiry or otherwise, are given to the best of our knowledge and are believed to be reliable. Our products and related information are provided for industrial users possessing the necessary knowledge and practical skills, and it is the end user's responsibility to determine whether the product is suitable for the specific use. The buyer, having performed such evaluation, proceeds entirely at its own risk.

The quality and condition of the substrate on site, and the many other factors affecting product use and application, are beyond PPG's control. Therefore, PPG accepts no liability for any loss, injury or damage arising from the use of the information in this product data sheet (unless otherwise provided in a written agreement). Different application environments, changes to the application process or extrapolation of the reference data may result in failure to achieve the expected coating quality.

This product data sheet supersedes all previous versions. The buyer is responsible for confirming that the data sheet in hand is the latest version before using the product. The latest version is published on the official website of PPG Protective & Marine Coatings:

www.ppgpmc.com. In case of discrepancy between the Chinese version and the original English version of the product data sheet, the English original shall prevail.

The PPG Logo, Bringing innovation to the surface., and other PPG marks are property of the PPG group of companies. All other third-party marks are property of their respective owners.