Jotatop AY10 WF waterborne acrylic topcoat AY10 is a waterborne paint used as a topcoat. Marine coatings segment: suitable for various marine structures. Used as part of a complete waterborne system over JOTUN-recommended waterborne primers, or as part of a mixed system over suitable solvent-borne primers. Parameters on this page: volume solids 37 ± 2%, dry film thickness 40–60 µm, theoretical spreading rate 9.3–6.2 m²/L. Comparable products of the same brand and type: Jota AY10 LH waterborne acrylic environmentally friendly topcoat, Jota AY30T WF fast-drying waterborne acrylic primer-topcoat, Jotatop AY20 WF waterborne acrylic topcoat AY20.
Parameter source: JOTUN manufacturer's Technical Data Sheet (TDS) "Jotatop AY10 WF waterborne acrylic topcoat AY10"; values such as spreading rate are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 37 ± 2% |
|---|---|
| Dry Film Thickness | 40–60 µm |
| Theoretical Spreading Rate | 9.3–6.2 m²/L |
| VOC | GB/T 23986-2009 10.4 45 g/L (China) |
| Density / Specific Gravity | 1.2 kg/L |
| Number of Components | One-component |
| Thinner | Water |
| Gloss | Semi-gloss (35–70) |
| Wet Film Thickness | 110–160 µm |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Waterborne acrylic topcoat AY10
This is a one-component waterborne acrylic coating. It is a general-purpose, fast-drying product for interior use. It dries at temperatures as low as 10°C. Used as a topcoat in atmospheric environments.
Used as part of a complete waterborne system over JOTUN-recommended waterborne primers, or as part of a mixed system over suitable solvent-borne primers. The product is part of a certified system that does not propagate surface flame.
Marine coatings:
Suitable for various offshore structures. Recommended for accommodation areas and machinery spaces.
Others
Certified compliant with the low flame-spread requirements of the IMO 2010 FTP Code. Other certificates and approvals are available on request.
White, grey, green
| Property | Test / Standard | Description |
| Volume Solids | ISO 3233 | 37± 2 % |
| Gloss (GU 60°) | ISO 2813 | Semi-gloss (35–70) |
| Density | Theoretical Value | 1.2 kg/L |
| Region | Regulations | Test / Standard | VOC Value |
| China | GB 30981-2020 Limit of harmful substances of industrial protective coatings | GB/T 23986-2009 10.4 45 g/L |
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
VOC measured value (g/L) determined in accordance with HJ 2537-2014: 45
Typical recommended specification range
| Dry Film Thickness | 40–60 µm |
| Wet Film Thickness | 110–160 µm |
| Theoretical Spreading Rate | 9.3–6.2 m²/L |
Surface Preparation
| Substrate | Minimum | Recommended |
| Coated surface | A clean, dry and sound compatible primer. | |
This product may be applied by the following methods
| Spray: | Apply by airless spray. |
| Brush: | Recommended for touch-up and small-area application. Take care to achieve the specified dry film thickness. |
| Roller: | Use a suitable roller. With roller application, take care to apply sufficient material to achieve the specified dry film thickness. |
One-component
| Thinner | Water |
|---|
| Nozzle tip size (inch/1000): | 13-19 |
| Nozzle pressure (minimum): | 150 bar/2100 psi |
| Substrate Temperature | 10 °C | 23 °C | 40 °C |
| Touch Dry | 1 h | 40 min | 10 min |
| Walk-on Dry | 1.5 h | 1 h | 30 min |
| Minimum recoat interval | 2 h | 1.5 h | 1 h |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Temperature
| Continuous | Peak | |
| Drying, atmospheric | 80 °C | - |
Depending on the actual exposure conditions in service, this product may be used with various primers and topcoats. Some reference systems are listed below. For specific systems, contact JOTUN.
| Previous Coat | Acrylic |
|---|
Preparation and cleaning of application equipment. To avoid contamination of water-borne paint by solvent, spray equipment must be cleaned before use. All equipment containing solvent, such as pumps, lines and guns, must be thoroughly cleaned in accordance with the following instructions.
If the application equipment is stainless steel, designed for and used only with water-borne coatings, this preparation and cleaning procedure is not required.
Before spraying:
Flush equipment and lines with JOTUN Thinner No. 17, then with Thinner No. 4, and finally with fresh water.
After spraying:
Clean equipment and lines with water and an alkaline degreaser, then flush with JOTUN Thinner No. 4, and finally with JOTUN Thinner No. 17.
Volume Container size
| (L) | ||
| Jotatop AY10 WF Water-borne Acrylic Topcoat AY10 | 5 / 20 | |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
Protect from frost during transport and storage.
Jotatop AY10 WF 24 months water-based acrylic topcoat AY10
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling coating, products may show slight colour variation from batch to batch. Such products, and epoxy products used as topcoats, may chalk when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, application quality and product type. Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
