Jota AY10 LH Water-borne Acrylic Environment-friendly Topcoat is a water-borne coating used as a topcoat. In the marine sector: suitable for various marine structures. Used as part of a complete water-borne system over Jotun-recommended water-borne primers, or as part of a mixed system over suitable solvent-borne primers. Parameters on this page: volume solids 33 ± 2%; dry film thickness 30–40 µm; theoretical spreading rate 11–8.3 m²/L. Comparable products from the same brand: Jota AY30T WF Fast-drying Water-borne Acrylic Primer-topcoat, Jotatop AY10 WF Water-borne Acrylic Topcoat AY10, Jotatop AY20 WF Water-borne Acrylic Topcoat AY20.
Source: JOTUN original technical data sheet (TDS) 'Jota AY10 LH Water-borne Acrylic Environment-friendly Topcoat'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 33 ± 2% |
|---|---|
| Dry Film Thickness | 30–40 µm |
| Theoretical Spreading Rate | 11–8.3 m²/L |
| VOC | 28 g/L |
| Density / Specific Gravity | 1.5 kg/L |
| Number of Components | One-component |
| Flash Point | 101 °C |
| Thinner | Water |
| Gloss | Matt (0–35) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Water-borne Acrylic Environment-friendly Topcoat (6CK)
A one-component water-borne acrylic coating. A general-purpose product suitable for interior use. Can dry at temperatures down to 10 °C. Used as a topcoat in atmospheric environments.
Used as part of a complete water-borne system over Jotun-recommended water-borne primers, or as part of a mixed system over suitable solvent-borne primers.
This product is part of a certified complete system with non-spreading surface flame.
Marine coatings:
Suitable for various offshore structures. Recommended for accommodation areas and machinery spaces.
Others
White
| Property | Test / Standard | Description |
| Volume Solids | ISO 3233 | 33± 2 % |
| Gloss (GU 60°) | ISO 2813 | Matt (0–35) |
| Flash Point | ISO 3679 Method 1 | 101 °C |
| Density | Theoretical Value | 1.5 kg/L |
| VOC — EU | IED (2010/75/EU) (theoretical value) | 28 g/L |
| VOC — China | GB/T 23986-2009 (tested) | 61 g/L |
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
Typical recommended specification range
| Dry Film Thickness | 30–40 µm |
| Wet Film Thickness | 90–120 µm |
| Theoretical Spreading Rate | 11–8.3 m²/L |
To ensure lasting adhesion of the next coat, all surfaces must be clean, dry and free of contaminants.
Surface Preparation
| Substrate | Minimum | Recommended | |
| Coated surface; clean, dry and intact compatible primer (compliant with ISO | Clean, dry and intact compatible primer (compliant with ISO | ||
| 12944-4 | clause 6.1.4). | 12944-4 | clause 6.1.4). |
This product may be applied by the following methods
| Spray: | Apply by air spray or airless spray. |
| Brush: | Recommended for touch-up and small-area application. Take care to achieve the specified dry film thickness. |
| Roller: | Use a suitable roller. With roller application, take care to apply sufficient material to achieve the specified dry film thickness. |
One-component
| Thinner | Water |
|---|
| Nozzle tip size (inch/1000): | 13-17 |
| Nozzle pressure (minimum): | 150 bar / 2100 psi |
| Substrate Temperature | 10 °C | 23 °C | 40 °C |
| Touch Dry | 2 h | 1 h | 0.5 h |
| Walk-on Dry | 8 h | 6 h | 4 h |
| Minimum recoat interval | 4 h | 2 h | 1 h |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Temperature
| Continuous | Peak | |
| Drying, atmospheric | 60 °C | - |
At the above temperatures, protective performance is unaffected, but appearance may be affected.
Depending on the actual exposure conditions in service, this product may be used with various primers and topcoats. Some reference systems are listed below. For specific systems, contact JOTUN.
| Previous Coat | Acrylic |
|---|
Preparation and cleaning procedure for application equipment:
To avoid contaminating the water-borne paint with solvent, spray equipment shall be cleaned before use. All solvent-containing pumps, hoses and guns shall be cleaned thoroughly according to the following instructions.
If the application equipment is stainless steel, designed for and used only with water-borne coatings, this preparation and cleaning procedure is not required.
Before spraying:
Flush equipment and lines with JOTUN Thinner No. 17, then with Thinner No. 4, and finally with fresh water.
After spraying:
Clean equipment and lines with water and an alkaline degreaser, then flush with JOTUN Thinner No. 4, and finally with JOTUN Thinner No. 17.
| Volume | Container Size | |
| (L) | ||
| Water-borne Acrylic Environment-friendly Topcoat | 20 | |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
Water-borne Acrylic Environment-friendly Topcoat, 24 months
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge.
Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling, products may show slight colour variation from batch to batch. Likewise, fading and chalking may occur when exposed to sunlight.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
