Jotatemp 1000 HT Two-component Titanium-catalysed Inorganic Ceramic Copolymer Coating is a heat-resistant coating. Industrial protective coatings: suitable for stainless steel, alloy steel (P91) and ceramic insulated and non-insulated substrate surfaces. Designed as a heat-resistant coating that, where the substrate permits, continuously withstands low temperatures down to −196 °C and high temperatures up to 1000 °C. Parameters on this page: volume solids 72 ± 2%, dry film thickness 100–150 µm, theoretical spreading rate 7.2–4.8 m²/L.
Source: JOTUN original technical data sheet (TDS) "Jotatemp 1000 HT Two-component Titanium-catalysed Inorganic Ceramic Copolymer Coating"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 72 ± 2% |
|---|---|
| Dry Film Thickness | 100–150 µm |
| Theoretical Spreading Rate | 7.2–4.8 m²/L |
| VOC | 306 g/L (US) |
| Density / Specific Gravity | 1.8 kg/L |
| Number of Components | Two-component |
| Flash Point | 24 °C |
| Thinner | Jotun Thinner No. 7 / JOTUN Thinner No. 10, JOTUN Thinner No. 7… |
| Mixing Ratio | 110 parts : 1 part (by volume) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Jotatemp 1000 HT
A two-component titanium-catalysed inorganic ceramic copolymer coating curing at ambient temperature. It belongs to the polymer coating class. Designed as a heat-resistant coating that, where the substrate permits, continuously withstands low temperatures down to −196 °C and high temperatures up to 1000 °C. Can be used as a primer or topcoat in atmospheric environments. Suitable for suitably surface-prepared stainless steel, alloy steel (P91) and ceramic substrate surfaces. Can be used on hot substrates up to 250 °C. Refer to the application guide for more detailed information.
Industrial protective coatings:
Suitable for stainless steel, alloy steel (P91) and ceramic insulated and non-insulated substrate surfaces. For other substrates and temperature ranges, contact the local JOTUN office. Specially designed to prevent corrosion under insulation (CUI) above 204 °C. Can be used on non-insulated carbon steel substrates at continuously sustained temperatures above 200 °C. For excellent performance on carbon steel substrates, Jotatemp 1000 is recommended.
Others
C5H testing completed per ISO 12944-6:2018 on stainless steel and alloy steel (P91) substrates.
Passed the 1000-hour 450 °C dry heat test on stainless steel substrates.
Passed the 1000-hour 540 °C dry heat test on alloy steel (P91) substrates.
Passed a 1000-hour dry heat test at 1000 °C on ceramic substrates.
For certificates and approvals regarding high- and low-temperature service, contact the local JOTUN office.
Other certificates and approvals are available on request.
Jotatemp 1000 Inorganic Ceramic Inert Copolymer Heat-resistant Coating 1000 (6KS) for carbon steel.
For the different products in this series, refer to the respective technical data sheets
Dark grey, aluminium, aluminium effect (colour close to RAL 9006)
| Property | Test / Standard | Description |
| Volume Solids | ISO 3233 | 72± 2 % |
| Gloss (GU 60°) | ISO 2813 | Matt (0–35) |
| Flash Point | ISO 3679 Method 1 | 24 °C |
| Density | Theoretical Value | 1.8 kg/L |
| Region | Regulations | Test / Standard | VOC Value |
| US | CARB(SCM)2020 / SCAQMD rule 1113 | Calculation | 306 g/L |
| Hong Kong | Air Pollution Control (VOC) Regulation | Calculation | 306 g/L |
| EU | European Paint Directive 2004/42/CE | Calculation | 306 g/L |
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
Typical recommended specification range
| Dry Film Thickness | 100–150 µm |
| Wet Film Thickness | 140–210 µm |
| Theoretical Spreading Rate | 7.2–4.8 m²/L |
In a single-coat system, it can be applied up to a dry film thickness of 200 µm.
Surface Preparation
| Substrate | Minimum | Recommended |
| Stainless steel | The surface should be blasted with a non-metallic abrasive, | “Blast clean using an approved non-metallic abrasive |
| hand- or machine-sanded using abrasive paper or fibre discs, | to produce a sharp angular surface profile.” |
to produce scratch marks on the surface.
| Alloy steel (P91) | The surface should be blasted with a non-metallic abrasive, | “Blast clean using an approved non-metallic abrasive |
| hand- or machine-sanded using abrasive paper or fibre discs, | to produce a sharp angular surface profile.” |
| Ceramic substrates | The surface shall be clean and dry. | |
| Coated surface | A clean, dry and sound compatible primer. | |
This product may be applied by the following methods
| Spray: | Apply by airless spray. |
| Brush: | Recommended for touch-up and small-area application. Take care to achieve the specified dry film thickness. |
| Jotatemp 1000 HT Comp A | 110 parts |
| Jotatemp 1000 Comp B — Inorganic Ceramic Inert Copolymer Heat-Resistant Coating 1000, Component B | 1 part |
Mix component A thoroughly before adding component B.
| Thinner | Jotun Thinner No. 7 / JOTUN Thinner No. 10. JOTUN Thinner No. 7. For ideal spray performance, this product may be thinned by 3–5% by volume before use. |
|---|---|
| Note | Where the Korean VOC regulation (Clean Air Conservation Act) and its corresponding thinning limits differ from the recommended thinning volume, the former prevails. |
| Nozzle tip size (inch/1000): | 17-23 |
| Nozzle pressure (minimum): | 150 bar/2100 psi |
| Substrate Temperature | 10 °C | 15 °C | 23 °C | 40 °C | 100 °C |
| Touch Dry | 5 h | 3 h | 2 h | 1.5 h | 15 min |
| Walk-on Dry | 22 h | 18 h | 5 h | 3 h | 15 min |
| Minimum recoat interval | 24 h | 18 h | 6 h | 3.5 h | 0 min |
| Dry/cured to service | 4 days | 3 days | 24 h | 18 h | 15 min |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
As it evaporates rapidly above 100 °C, flash drying may occur.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Dry/cured to service: the minimum time before the coating can be permanently exposed to a specific environment/medium.
| Paint temperature | 10 °C | 23 °C | 40 °C |
| Pot Life | 10 h | 6 h | 4 h |
Stainless steel:
| Continuous | 450 °C |
|---|
Alloy steel (P91):
| Continuous | 540 °C |
|---|
Ceramic substrates:
| Continuous | 1000 °C |
|---|
The continuous service temperature limit is based on the heat resistance of the substrate.
Depending on the actual exposure conditions in service, this product may be used with various primers and topcoats. Some reference systems are listed below. For specific systems, contact JOTUN.
| Previous coat: | Zinc silicate, inert copolymer matrix, itself |
| Subsequent coat: | Silicone acrylic |
| Volume | Container Size | |
| (L) | ||
| Jotatemp 1000 HT Comp A | 4.4 | 5 |
| Jotatemp 1000 Comp B — Inorganic Ceramic Inert Copolymer Heat-Resistant Coating 1000, Component B | 0.04 | 0.25 |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
Storage temperature shall not exceed 40 °C.
| Jotatemp 1000 HT Comp A | 12 months |
| Jotatemp 1000 Comp B — Inorganic Ceramic Inert Copolymer Heat-Resistant Coating 1000, Component B | 24 months |
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling coating, products may show slight colour variation from batch to batch. Such products, and epoxy products used as topcoats, may chalk when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, application quality and product type. Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
