Balloxy HB Light Epoxy Ballast Tank Coating is an epoxy paint. Specially used for maintenance and repair of ship ballast water tanks and marine engineering. Suitable for suitably prepared carbon steel, galvanized steel, stainless steel, aluminium and many aged coated surfaces. Parameters on this page: volume solids 82 ± 2%, dry film thickness 125–300 µm, theoretical spreading rate 6.6–2.7 m²/L. Comparable products of the same brand: Jota Armour Strong Abrasion-resistant Epoxy Non-slip Coating, Jotacote HF002 Universal Abrasion-resistant Epoxy HF, Jotacote UHB Ultra-strong Epoxy High-build UHB.
Data source: JOTUN original Technical Data Sheet (TDS), "Balloxy HB Light Epoxy Ballast Tank Coating"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 82 ± 2% |
|---|---|
| Dry Film Thickness | 125–300 µm |
| Theoretical Spreading Rate | 6.6–2.7 m²/L |
| VOC | 245 g/L |
| Density / Specific Gravity | 1.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 35 °C |
| Thinner | JOTUN Thinner No. 17 |
| Mixing Ratio | 5 parts : 1 part : 3 parts : 1 part (by volume) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Epoxy Ballast Tank Coating (0BR)
This is a two-component, polyamine-cured surface-tolerant epoxy coating. It is a high-build product featuring surface tolerance and high solids content. Specially used for areas where ideal surface preparation cannot or need not be achieved. Provides long-term anti-corrosion protection in highly corrosive environments. In atmospheric and immersed environments it can be used as a primer, intermediate coat or topcoat. Suitable for suitably prepared carbon steel, galvanized steel, stainless steel, aluminium and many aged coated surfaces. Can be applied at surface temperatures below 0 °C.
Specifically for the maintenance and repair of ship ballast water tanks and marine structures.
Others
Certified according to IMO Res.215(82) and suitable for the PSPC standard for ballast water tanks. Other certificates and approvals are available on request.
Cream, green
Property Test/Standard Description
Ambient-curing
| Volume Solids | ISO 3233 | 82± 2 % |
| Gloss (GU 60°) | ISO 2813 | Semi-gloss (35–70) |
| Flash Point | ISO 3679 Method 1 | 35 °C |
| Density | Theoretical Value | 1.4 kg/L |
| VOC — USA / Hong Kong | US EPA Method 24 (test value) (CARB (SCM) 2007, SCAQMD Rule 1113, Hong Kong) | 245 g/L |
| VOC — EU | IED (2010/75/EU) (theoretical value) | 240 g/L |
| VOC — China | GB/T 23985-2009 (tested) | 203 g/L |
| VOC — China | GB/T 23985-2009 (8.3, tested) | No data. |
| VOC — China | GB/T 23985-2009 (8.4, tested) | No data. |
| VOC — China | GB/T 23986-2009 (10.3, tested) | No data. |
| VOC — China | GB/T 23986-2009 (10.4, tested) | No data. |
| VOC — China | GB/T 34682-2017 (tested) | No data. |
Winter grade
| Volume Solids | ISO 3233 | 71± 2 % |
| Flash Point | ISO 3679 Method 1 | 35 °C |
| Density | Theoretical Value | 1.4kg/L |
| VOC — USA / Hong Kong | US EPA Method 24 (test value) (CARB (SCM) 2007, SCAQMD Rule 1113, Hong Kong) | 310 g/L |
| VOC — EU | IED (2010/75/EU) (theoretical value) | 272 g/L |
| VOC — China | GB/T 23985-2009 (tested) | 194 g/L |
| VOC — China | GB/T 23985-2009 (8.3, tested) | No data. |
| VOC — China | GB/T 23985-2009 (8.4, tested) | No data. |
| VOC — China | GB/T 23986-2009 (10.3, tested) | No data. |
| VOC — China | GB/T 23986-2009 (10.4, tested) | No data. |
| VOC — China | GB/T 34682-2017 (tested) | No data. |
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
Typical recommended specification range
| Dry Film Thickness | 125–300 µm |
| Wet Film Thickness | 150–365 µm |
| Theoretical Spreading Rate | 6.6–2.7 m²/L |
| Dry Film Thickness | 125–300 µm |
| Wet Film Thickness | 175–420 µm |
| Theoretical Spreading Rate | 5.7–2.4 m²/L |
Surface Preparation
| Substrate | Minimum | Recommended |
| Carbon Steel | St 2 (ISO 8501-1) | Sa 2½ (ISO 8501-1) |
| Stainless steel | Blast clean with approved non-metallic abrasive to produce a sharp, angular rough surface. | |
| Aluminium | ||
| Galvanised steel | The surface should be clean, dry and have a suitable profile | Sweep blast with a non-metallic abrasive to produce a clean, |
| ° | a rough and uniform surface. | |
| Shop-primed Steel | Clean, dry and intact shop primer (compliant with ISO 12944-4 clause 5.4). | Sa 2 (ISO 8501-1) |
| Coated surface | A clean, dry and sound compatible primer. | |
This product may be applied by the following methods
| Spray: | Apply by airless spray. | |
| Brush: | Recommended for touch-up and small-area application. Take care to achieve the specified dry film thickness. | |
| Roller: | Suitable for small areas. | Not recommended for the first primer coat. Take care to achieve the specified dry film thickness. |
| Epoxy Ballast Tank Coating, Component A | 5 parts |
| Epoxy Ballast Water Tank Coating, Component B | 1 part |
| Epoxy Ballast Tank Coating, Component A | 3 parts |
| Epoxy Ballast Water Tank Coating, Component B (Winter Grade) | 1 part |
| Thinner | JOTUN Thinner No. 17 |
|---|
In China, the cleaning solvent must comply with GB 38508-2020
| Nozzle tip size (inch/1000): | 19-23 |
| Nozzle pressure (minimum): | 150 bar/2100 psi |
Substrate temperature -5 °C 0 °C 5 °C 10 °C 23 °C 40 °C Ambient-curing
| Touch Dry | 8 h | 4 h | 2 h |
| Walk-on Dry | 24 h | 10 h | 4 h |
| Minimum recoat interval | 24 h | 10 h | 4 h |
| Dry/cured to immersion | 7 days | 2 days | 1 day |
| Dry/cured to service | 14 days | 7 days | 2 days |
| Touch Dry | 24 h | 18 h | 12 h | 6 h | 2.5 h |
| Walk-on Dry | 48 h | 26 h | 18 h | 12 h | 5 h |
| Minimum recoat interval | 48 h | 26 h | 18 h | 12 h | 5 h |
| Dry/cured to immersion | 10 days | 9 days | 7 days | 3 days | 1 day |
| Dry/cured to service | 21 days | 14 days | 7 days | 3 days | 2 days |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Dry/cured to immersion: the minimum time before the coating can be permanently immersed in sea water.
Dry/cured to service: the minimum time before the coating can be permanently exposed to a specific environment/medium.
| Paint temperature | 23 °C |
| Ambient-curing | |
|---|---|
| Induction Time | 10 min |
| Pot Life | 2 h |
| Winter grade | |
| Induction Time | 10 min |
| Pot Life | 1.5 h |
Temperature
| Drying, atmospheric | Continuous 90 °C | Peak - |
| Immersed, sea water | 50 °C | 60 °C |
Withstands peak temperatures for a maximum of one hour.
At the above temperatures, protective performance is unaffected, but appearance may be affected.
Note: this coating can withstand different immersion temperatures, depending on the specific chemical and whether immersion is continuous or intermittent. Heat resistance is affected by the coating system as a whole. When used with other coatings, ensure that all coatings in the system have similar heat resistance.
Depending on the actual exposure conditions in service, this product may be used with various primers and topcoats. Some reference systems are listed below. For specific systems, contact JOTUN.
| Previous coat: | Inorganic zinc shop primer, epoxy, modified epoxy |
| Subsequent coat: | Modified epoxy |
| Volume | Container Size | |
| (L) | ||
| Epoxy Ballast Tank Coating, Component A | 15 | 20 |
| Epoxy Ballast Water Tank Coating, Component B | 3 | |
| Epoxy Ballast Water Tank Coating, Component B (Winter Grade) | 5 | |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Epoxy Ballast Tank Coating, Component A | 48 months |
| Epoxy Ballast Water Tank Coating, Component B | 48 months |
| Epoxy Ballast Water Tank Coating, Component B (Winter Grade) | 48 months |
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling coating, products may show slight colour variation from batch to batch. Such products, and epoxy products used as topcoats, may chalk when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, application quality and product type. Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
