Interstores Alkyd Primer Multipurpose Primer is an alkyd coating used as a primer. For maintenance of above-water areas. Interstores Alkyd Primer is a surface-tolerant coating compatible with most substrates and overcoatable with a range of topcoats. Parameters on this page: volume solids 48% ± 2%, dry film thickness 75 µm, theoretical spreading rate 6.4 m²/L. Comparable products from the same brand: Interbond 201 – Temperate Epoxy Primer, Interbond 808 Epoxy Anticorrosive, Intergard 5101 Universal Epoxy Primer.
Source: International original technical data sheet (TDS) "Interstores Alkyd Primer Multipurpose Primer"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 48% ± 2% |
|---|---|
| Dry Film Thickness | 75 µm |
| Theoretical Spreading Rate | 6.4 m²/L |
| VOC | 412 g/L (as supplied) (EPA Method 24) 362 g/kg (… |
| Density / Specific Gravity | — |
| Number of Components | One-component |
| Mixing Ratio | N/A |
| Colour / Appearance | ISA710 white, ISA720 grey, ISA730 red |
| Gloss | Matt |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A fast-drying, one-component primer. Interstores Alkyd Primer is a surface-tolerant coating compatible with most substrates and overcoatable with a range of topcoats.
For maintenance of above-water areas.
For in-service maintenance only.
| Colour | ISA710 white, ISA720 grey, ISA730 red |
|---|---|
| Topcoat/gloss | Matt |
| Component B (curing agent) | N/A |
| Volume Solids | 48% ±2% (ISO 3233:1998) |
| Mixing ratio | N/A |
| Standard film thickness | 75 µm dry film (156 µm wet film) |
| Theoretical Spreading Rate | At 75 µm dry film thickness, theoretical spreading rate is 6.4 m²/L, allowing an appropriate loss factor |
| Application Methods | Airless spray, brush, roller |
| Flash Point | Single component 41 °C |
| Induction Time | Not required |
| Drying data | 5°C | 15°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 2.5 h | 2 h | 1.5 h | 60 min |
| Hard dry [ISO 9117-1:2009] | 4 h | 3.5 h | 3 h | |
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 5°C | 15°C | 25°C | 35°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Interlac 665 | 6 h | 3 days | 6 h | 2 days | 60 min | 2 days | 60 min | 2 days |
| Intersheen 579 | 6 h | 2 days | 6 h | 2 days | 2 h | 2 days | 2 h | 2 days |
| Interstores Alkyd | 6 h | 3 days | 6 h | 2 days | 2 h | 2 days | 2 h | 2 days |
| Interstores Alkyd | 3 h | 1 month | 3 h | 1 month | 2 h | 1 month | 2 h | 1 month |
Primer
| Interstores | 24 h 7 days 24 h 7 days 16 h 7 days 16 h 7 days Polyurethane |
|---|---|
| Interthane 990 | 24 h 7 days 24 h 7 days 16 h 7 days 16 h 7 days |
| Volatile Organic Compounds | 412 g/L (as supplied) (EPA Method 24) 362 g/kg (as supplied liquid paint). EU Solvent Emissions Directive (Commission Directive 1999/13/EC). VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|
When used as part of an approved scheme, this coating holds the following certificates: • Food contact – grain cargo (NOHH) • Fire resistance – meets low flame spread requirements (Exova Warringtonfire) • Fire resistance – "smoke and toxicity" (Exova Warringtonfire) • Fire resistance – complies with the Marine Equipment Directive. For details, consult your local representative.
For the paint system best suited to the surface to be protected, consult your local representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
Maintenance/in-service: treat repair areas to at least SSPC-SP2. Higher standards of surface preparation, such as abrasive blasting to SSPC-SP6 or ultra-high-pressure water cleaning to HB2M (International Paint ultra-high-pressure water cleaning standard), improve product performance.
Sand or scrape the area around damaged film to a firm edge.
Ensure the area is clean and dry before applying Interstores Alkyd Primer.
The primer overlaps the existing coating by about 2–3 cm.
For specific advice, consult your local representative.
Note: for marine environments in North America, the following surface preparation standards may be used: SSPC-SP6 in place of Sa2 (ISO 8501-1:2007), SSPC-SP2 in place of St2 (ISO 8501-1:2007).
This coating is a single-component product; stir thoroughly with a power mixer before application.
International GTA004. Normally no thinning is required. Under extreme conditions, consult your local representative for application advice. Do not thin beyond the limits of local environmental regulations.
Recommended nozzle size 0.53–0.66 mm (21–26 thou); total output fluid pressure at the nozzle not less than 176 kg/cm² (2500 psi)
Conventional spray application is not recommended.
Brush application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Roller application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Flush all equipment thoroughly with International thinner. All unused paint must be stored in tightly closed containers. Partly filled containers may show increased viscosity after storage. Strain the paint before use.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; China — tel. (86) 532 83889090; other regions — contact the regional office.
Overcoating Interstores Alkyd Primer with epoxy coatings is not recommended.
In some areas, for specific customer requirements and where decorative appearance is not required, Interstores Alkyd Primer may be used without a decorative topcoat. Consult the regional technical centre for application instructions and colour range.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specifically instructed, raise the paint temperature to between 21 and 27 °C before mixing and application to achieve optimum application performance. Unmixed paint (in sealed containers) must be stored protectively as specified in the Storage section of this product data sheet. The technical and application data given here are intended as general guidance for establishing an application procedure. Test results are obtained in a controlled laboratory environment, and International Paint does not claim that the published test results, or any other test results, accurately represent results obtained in all site environments. Because application, environmental and design parameters vary widely, care must be exercised in coating selection, performance verification and use.
Packaging size volume; packaging
| 20 L | 20 L. For other packaging sizes, consult International Paint. |
|---|
| Packaging Specifications | Packaging weight |
|---|---|
| 20 L | 26.7 kg |
| Shelf life | At 25 °C, minimum 24 months. Thereafter, re-inspection is required. Store in a dry, sheltered place away from heat and sources of ignition |
|---|
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
The in-plant item numbers of Interstores Alkyd Primer Multipurpose Primer are as follows.Item No.is the most accurate form when ordering;Colour/colour codecorresponds to the actual colour (RAL, GSB are colour chart codes);Packaging SpecificationsFactory complete-set specification format. Colors not listed may be ordered against the colour card.
| Item No. | Colour / colour code | Packaging Specifications |
|---|---|---|
| ISA730 Red | — | 20 L |
This model has a total of1item numbers, all listed on this page; colours outside the table (including special colours and bulk packaging) can be confirmed by phone, delivery dates are advised according to the factory's current production schedule and stock. In the packaging specification, the "+" indicates the complete-set notation for two-component products (base + curing agent), subject to the factory specification; a "—" in the colour column denotes an auxiliary product, or that the item has no colour code in the factory system.
