Intershield One-2-One - Red Epoxy Primer is an epoxy coating used as a primer. Suitable for use with controlled cathodic protection. Designed as a crew-friendly (easy for crew application) two-component universal primer for in-service maintenance (<340g/L),specifically designed with an equal mixing ratio to simplify mixing and reduce waste.Parameters on this page: Volume Solids 67% ± 2%, Dry Film Thickness 75 µm, Theoretical Spreading Rate 8.93 m²/L.Comparable models of the same brand: Interbond 201 - Temperate Epoxy Primer, Interbond 808 Epoxy Anticorrosive, Intergard 5101 Epoxy Universal Primer.
Source: INTERNATIONAL original technical data sheet (TDS) 'Intershield One-2-One - Red Epoxy Primer'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 67% ± 2% |
|---|---|
| Dry Film Thickness | 75 µm |
| Theoretical Spreading Rate | 8.93 m²/L |
| VOC | 292 g/L (as supplied) (EPA Method 24); 244 g/kg (… |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B = 1:1 (by volume) |
| Colour / Appearance | IIA122 red (Intershield One-2-One aluminium -… |
| Gloss | Semi-gloss |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Red epoxy primer: a surface-tolerant, general-purpose pure epoxy primer used as an anti-rust repair coating, providing high anti-rust protection and low-temperature application performance.
Designed as a crew-friendly (easy-to-apply) two-component general-purpose in-service maintenance primer (<340 g/L), specially designed with an equal mixing ratio to simplify mixing and reduce waste.
Used as a general-purpose anticorrosive primer for in-service maintenance.
Suitable for use with impressed current cathodic protection.
| Colour | IIA122 red (Intershield One-2-One aluminium IIA121 has a separate product data sheet) |
|---|---|
| Topcoat/gloss | Semi-gloss |
| Component B (curing agent) | IIA125 |
| Volume Solids | 67% ±2% (ISO 3233:1998) |
| Mixing ratio | Component A : Component B = 1:1 (by volume) |
| Standard film thickness | 75 µm dry film thickness (112 µm wet film thickness) |
| Theoretical Spreading Rate | At 75 µm dry film thickness, the theoretical spreading rate is 8.93 m²/L, allowing an appropriate loss factor |
| Application Methods | Airless spray, brush, roller |
| Flash Point | Component A 39 °C; Component B 27 °C; mixed 31 °C |
| Induction Time | N/A |
| Drying data | -5°C | 5°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 6 h | 4 h | 3 h | 60 min |
| Hard dry [ISO 9117-1:2009] | 28 h | 17 h | 4 h | 2 h |
| Pot life after mixing | 6 h | 2 h | 60 min | |
| Recoat data — see the “Limitations” section | Substrate Temperature |
|---|
| When recoating the following products | -5 °C minimum | -5 °C maximum | 5 °C minimum | 5 °C maximum | 25 °C minimum | 25 °C maximum | 35 °C minimum | 35 °C maximum |
| Intergard 740 | 30 h | 7 days | 18 h | 7 days | 6.5 h | 7 days | 4 h | 7 days |
h
| Intersheen 579 | 30 h, 2 days, 18 h, 2 days, 6.5 h, 24 h, 4 h, 24 h |
|---|---|
| Intershield One-2-One | 30 h, 14 days, 18 h, 14 days, 6.5 h, 14 days, 4 h, 14 days |
| Immersion areas | h |
| Intershield One-2-One | 30 h, 6 months, 18 h, 6 months, 6.5 h, 5.5 months, 4 h, 3 months |
| Non-immersion areas | h |
| Interstores | 30 h, 7 days, 18 h, 7 days, 6.5 h, 7 days, 4 h, 3 days |
| Polyurethane | h |
| Interthane 990 | 30 h, 3 days, 18 h, 3 days, 6.5 h, 3 days, 4 h, 3 days |
| Volatile Organic Compounds | 292 g/L (as supplied) (EPA Method 24); 244 g/kg (as supplied liquid paint). EU Solvent Emissions Directive (Commission Directive 1999/13/EC). VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerance. |
|---|
Coating hazards GB 30981.2-S-Pb≤1000-NC; complies with GB 30981.2-2025
When used as part of an approved scheme, the product holds the following certificates: • Food contact — complies with US FDA regulations for dry foodstuffs • Food contact — grain cargoes (NOHH) • Potable water — potable water cargoes (NSF-WRc) (BS6920). Certificates for potable water tanks issued by external bodies depend on the formulation and/or place of manufacture. As such, products supplied in different countries may not be approved to all the standards listed above.
Intershield One-2-One has also been tested according to the following standards, depending on the formulation and/or place of manufacture: - Ballast water tanks — IMO PSPC WBT (LR). Confirm the certificate status with the local representative.
For immersed areas, Intershield One-2-One red must be applied over Intershield One-2-One aluminium within the specified recoat interval.
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
In-service maintenance — bare steel and corroded areas: clean by hand or power tool at least to St2 (ISO 8501-1:2007). Note: all mill scale shall be removed; areas not suitably treated by chipping or needle gun shall be spot-blasted at least to Sa2 (ISO 8501-1:2007). Generally, this method is suitable for grade C or D steel.
Intershield One-2-One is suitable for application over aged existing coating systems. When overcoating chalked aged coatings or exposed topcoats, lightly abrade the surface before applying the Interstores primer. Loose or flaking coating should be scraped back to firmly adherent coating, the area to be coated should be abraded, and when applying Intershield One-2-One, ensure the overlap between the new coating and the existing coating is 2–3 cm (1
| in). | Before applying a full coat over a certain general type of coating, a small trial is recommended. |
|---|
For specific advice, consult your local representative.
Note: for marine environments in North America, the following surface preparation standards may be used: SSPC-SP6 in place of Sa2 (ISO 8501-1:2007), SSPC-SP2 in place of St2 (ISO 8501-1:2007).
The paint is supplied as a unit in two separate containers. Once a unit is mixed, it shall be used within the specified pot life.
| (1) | Prepare a separate container. |
|---|---|
| (2) | Stir the base (Component A) with a power stirrer and pour it all into a separate container. |
| (3) | Stir the curing agent (Component B) with a power stirrer, mix all of the curing agent (Component B) with the base (Component A), and stir thoroughly with a power stirrer. |
| (4) | If a small quantity is required, mix equal quantities of Component A and Component B in a second container. |
Normally no thinning is required. Under extreme conditions, consult your local representative for application advice. Do not thin beyond the limits of local environmental regulations.
Recommended nozzle tip size 0.48–0.64 mm (19–25 thou); total fluid pressure at the nozzle not less than 211 kg/cm² (3000 psi)
Conventional spray application is not recommended.
Recommended
Do not leave paint in hoses, spray guns or spray equipment. Flush all equipment thoroughly with International thinner. Once mixed, paint should not be resealed; if work is interrupted for too long, mix a fresh batch before resuming application.
All equipment shall be cleaned with International GTA220/GTA822 immediately after use. Spray equipment shall be flushed with this solvent. Periodically flushing spray equipment during the working day is good practice. The frequency of cleaning depends on factors such as the quantity sprayed, temperature and elapsed time (including interruptions). Pay close attention to the condition of the paint. Do not exceed the pot life after mixing.
All surplus paint and empty containers must be disposed of in accordance with appropriate local regulations/laws.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; China — tel. (86) 532 83889090; other regions — contact the regional office.
Optimum performance is obtained when this coating is applied to steel prepared to St 2 (ISO 8501-1:2007). Like all epoxy-based coatings, Intershield One-2-One chalks when exposed to UV light.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated shall be at least 3 °C above the dew point, and the relative humidity shall not exceed 85%. Unless otherwise instructed, for optimum application performance, bring the paint temperature to 21–27 °C before mixing and application. Unmixed paint (in tightly closed containers) shall be stored as specified in the 'Storage' section of this data sheet. The technical and application data herein are intended as general guidance for establishing a coating procedure.
Test performance results are obtained under controlled laboratory conditions; International Paint does not claim that the published test results, or any other tests, accurately represent the results obtained in all site environments. Because application, environmental and design factors vary greatly, care shall be taken in coating selection, performance verification and use.
| Packaging Specifications | Component A | Component B | ||
| Volume | Packaging | Volume | Packaging | |
| 10 L | 5 L | 5 L | ||
| 2 US gal | 1 US gal | 1 US gal | ||
For other packaging sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 10 L | 13.5 kg |
| 2 US gal | 23 lb |
| Shelf life | 12 months at 25 °C. Thereafter, re-inspection is required. Store in a cool, dry place away from heat and sources of ignition. |
|---|
Please consult INTERNATIONAL.
The information given in this product data sheet is not exhaustive. Anyone who uses, for any reason, any product other than those specifically recommended in this data sheet without first obtaining our written confirmation does so at their own risk as regards the suitability of the product for the intended purpose. Although we make every effort to ensure that all advice we give about the product (whether in this data sheet or otherwise) is correct, we cannot control the quality or condition of the substrate, nor the many factors affecting the application and use of this product. Accordingly, unless we specifically agree otherwise in writing, we accept no liability, to the maximum extent permitted by law, for any product performance problem arising, or for any loss or damage caused by use of the product. We therefore disclaim all warranties, express or implied, arising by operation of law or otherwise, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. All products supplied and all technical guidance provided are subject to our terms and conditions of sale. You should obtain a copy of this document and read it carefully. The information contained in this product data sheet may be amended at any time in the light of experience and of our continuing product development policy. Before using the product, it is the user's responsibility to check with the local representative that the data sheet in their possession is the latest version.
This technical data sheet is also available on our websites www.international-marine.com and www.international-pc.com, and should be consistent with this document. If there is any discrepancy between this document and the version of the technical data sheet on the website, the version on the website shall prevail.
© AkzoNobel, 2026www.international-marine.com
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
