HEMPEL Multi-purpose Waterborne Epoxy Paint 760 is a waterborne coating. It can be used as a primer on thermal-sprayed zinc and stainless steel surfaces, or as an intermediate coat in a waterborne system for moderate corrosive environments. HEMPEL Multi-purpose Waterborne Epoxy Paint 760 is a waterborne epoxy coating that can be applied to various substrates and has excellent adhesion. Parameters on this page: volume solids 50 ± 2%, dry film thickness 50 µm, theoretical spreading rate 10 m²/L. Comparable products of the same brand and category: HEMPEL Waterborne Epoxy Paint 184CN, HEMPEL Waterborne Epoxy Paint 18500 and HEMPEL Waterborne Epoxy Paint 48140.
Parameter source: HEMPEL manufacturer's Technical Data Sheet (TDS) "HEMPEL Multi-purpose Waterborne Epoxy Paint 760"; values such as spreading rate are converted from TDS parameters and are for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 50 ± 2% |
|---|---|
| Dry Film Thickness | 50 µm |
| Theoretical Spreading Rate | 10 m²/L |
| VOC | 96 g/L (China) |
| Density / Specific Gravity | 1.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 85°C |
| Colour / Appearance | Eggshell Grey 11320 |
| Gloss | Flat |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Paint 760
Hempel Waterborne Epoxy 760 is a waterborne epoxy paint that can be applied to a variety of different substrates with excellent adhesion. After curing, it forms a flexible, well-adhered film with good impact resistance. This product contains zinc phosphate.
Can be used as a primer on thermal spray zinc and stainless steel surfaces, or as an intermediate coat in waterborne systems for medium-corrosion environments.
| Product safety | Flash point 85°C |
|---|
| Regulations | Value |
| European Union | 58 g/L |
| USA (coatings) | 58 g/L |
| USA (regulatory) | 150 g/L |
| China | 96 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 18450 |
|---|---|
| Product components | Base 18459 |
Hardener 98151
| Standard colour / code | Eggshell Grey 11320 |
|---|
Light Grey 11320
| Gloss | Flat |
|---|---|
| Volume solids | 50 ± 2% |
| density | 1.4 kg/L |
| Recommended dry film thickness | 50 µm |
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 18459 : Hardener 98151 (93 : 7 by volume)
Stir thoroughly before use.
Thinner
Fresh water
Cleaning solvent
| Product temperature | 20°C |
|---|---|
| Pot Life | 4 h |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 15% | Nozzle pressure: 15 MPa; tip size: 0.38–0.43 mm |
If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Wet Film Thickness | 80 µm | 141 µm | 100 µm |
| Theoretical Spreading Rate | 12 m²/L | 7.1 m²/L | 10 m²/L |
To achieve optimum performance, avoid excessive film thickness. Depending on the end use and service area, the product may be specified at film thicknesses other than those indicated. This will alter the spreading rate, drying and curing times and recoat interval.
- If brush or roller application is used, more coats are required to achieve the specified dry film thickness.
| Surface temperature | 20°C |
| Surface Dry | 60 min |
| Through dry | 14 h |
| Fully cured | 7 days |
Measured at 50 µm dry film thickness under standard conditions; see Hempel's explanatory notes.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 12 months |
| Curing agent | 12 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| GWP (Global Warming Potential) | 9.2 g CO₂e/m² |
|---|
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
- Application methods - General application guide. This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
