HEMPEL's Solvent-free Epoxy Coating 570 belongs to epoxy coatings. The product may be used as a self-priming and self-finishing high-build coating, as a coating requiring surface tolerance, and in heavy-duty anti-corrosion applications requiring very low VOC. HEMPEL's Solvent-free Epoxy Coating 570 is a two-component solvent-free epoxy coating with good corrosion protection and good impact, abrasion and adhesion properties. Parameters on this page: volume solids 97 ± 2%, dry film thickness 150 µm, theoretical spreading rate 6.5 m²/L. Similar products from the same brand for comparison: HEMPEL's Fiber-containing High-strength Epoxy Coating 47510, HEMPEL's Multi-purpose Epoxy High-build Coating 500 Winter Grade, HEMPEL's Multi-purpose Epoxy High-build Coating 500.
Parameter source: HEMPEL original manufacturer Technical Data Sheet (TDS) for HEMPEL's Solvent-free Epoxy Coating 570; values such as spreading rate are converted from TDS parameters and are for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 97 ± 2% |
|---|---|
| Dry Film Thickness | 150 µm |
| Theoretical Spreading Rate | 6.5 m²/L |
| VOC | 57 g/L (China) |
| Density / Specific Gravity | 1.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 35°C |
| Colour / Appearance | Light grey 10500 ** |
| Gloss |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
570
HEMPEL's Solvent-free Epoxy Coating 570 is a two-component solvent-free epoxy coating with good corrosion protection and good impact, abrasion and adhesion properties. Suitable for application with standard airless spray equipment and easy to apply. It may also be applied in wet environments and under relatively simple surface preparation conditions.
The product may be used as a self-priming and self-finishing high-build coating, as a coating requiring surface tolerance, and in heavy-duty anti-corrosion applications requiring very low VOC. Suitable for full application in areas where climatic conditions are difficult to control and surface preparation is difficult, and for local application or repair in small areas with difficult access.
| Product safety | Flash point 35 °C |
|---|
| Regulations | Value |
| European Union | 57 g/L |
| USA (coatings) | 57 g/L |
| USA (regulatory) | 57 g/L |
| China | 57 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 3574M |
|---|---|
| Product components | Base 3574Z |
Curing Agent 98040
| Standard colour* / code | Light grey 10500 ** |
|---|---|
| Gloss | |
| Volume solids | 97 ± 2% |
| density | 1.4 kg/L |
| Recommended dry film thickness | 150 µm |
- The maximum permitted water-soluble salt level tested in accordance with ISO 8502-9 is 50 mg/m² (as NaCl).
- Before final painting, all shop primer breakdown and contamination incurred during storage and erection must be thoroughly cleaned by mechanical/chemical means.
570
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 3574Z : Hardener 98040 (2.5 : 1 by volume)
Stir thoroughly before use.
Thinner
No thinning required
(Not defined)
| Product temperature | 20°C |
|---|---|
| Pot Life | 60 min |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | No thinning required | Nozzle pressure: 28 MPa; nozzle tip size: 0.43–0.53 mm |
Thinning is not permitted. Spray parameters are indicative and may be adjusted according to site conditions. Pressure values apply to material at 20°C. (*For other application methods, consult the company's representative.)
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 100 µm | 200 µm | 150 µm |
| Wet Film Thickness | 103 µm | 206 µm | 155 µm |
| Theoretical Spreading Rate | 10 m²/L | 4.8 m²/L | 6.5 m²/L |
To achieve optimum performance, avoid excessive film thickness. Depending on the end use and service area, the product may be specified at film thicknesses other than those indicated. This will alter the spreading rate, drying and curing times and recoat interval. The practical consumption factor may vary with application conditions, equipment and workmanship. Checking paint consumption against area improves film thickness control.
- Depending on spray and curing conditions, some volatile reactants may evaporate. In addition, the curing process is accompanied by shrinkage. These two factors cause the actual volume solids and evaporation rate to be lower than the above values. Consult HEMPEL for more information.
| Surface temperature | 20°C | 10°C | 30°C | 40°C |
| Surface Dry | 8 h | 16 | 4½ | 2½ |
| Fully cured | 7 days | 14 | 5 | 3 |
570
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 10°C | 20°C | 30°C | 40°C | |
| Atmospheric, mild | |||||
|---|---|---|---|---|---|
| HEMPEL's Solvent-free Epoxy 570 | Minimum | 64 h | 16 h | 8 h | 4 h |
| Maximum | 28 days | 14 days | 7 days | 3½ days | |
| HEMPEL's Polyurethane Mastic Topcoat 5561B | Minimum | 4 days | 24 h | 12 h | 6 h |
| Maximum | Extendable* | ||||
| Atmospheric, moderate | |||||
| HEMPEL's Solvent-free Epoxy 570 | Minimum | 4 days | 24 h | 12 h | 6 h |
| Maximum | 28 days | 14 days | 7 days | 3½ days | |
| HEMPEL's Polyurethane Mastic Topcoat 5561B | Minimum | 4 days | 24 h | 12 h | 6 h |
| Maximum | Extendable* | ||||
| Atmospheric, severe | |||||
| HEMPEL's Solvent-free Epoxy 570 | Minimum | 4 days | 24 h | 12 h | 6 h |
| Maximum | 14 days | 7 days | 3½ days | 42 h | |
| HEMPEL's Polyurethane Mastic Topcoat 5561B | Minimum | 4 days | 24 h | 12 h | 6 h |
| Maximum | 14 days | 7 days | 3½ days | 42 h | |
Extendable* Depending on the actual exposure conditions, the coated surface may be recoated after an extended time. Contact your local Hempel representative for advice.
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Curing agent | 36 months |
| Binder | 24 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 6.5 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
570
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
