HEMPEL Multi-purpose Epoxy Paint 55800 is an epoxy coating. The product may also serve as a primer for outfitting components on various substrates, offering workable recoat intervals suited to most newbuilding schedules. HEMPEL Multi-purpose Epoxy Paint 55800 is a high solids epoxy topcoat whose tough film resists attack by seawater and mineral oils. Parameters on this page: volume solids 74 ± 2%, dry film thickness 100 µm, theoretical spreading rate 7.4 m²/L. Comparable models from the same brand: HEMPEL Fibre-reinforced Epoxy Paint 47510, HEMPEL Multi-purpose Epoxy High-build Paint 500 Winter grade, HEMPEL Multi-purpose Epoxy High-build Paint 500.
Parameter source: HEMPEL manufacturer technical data sheet (TDS) HEMPEL Multi-purpose Epoxy Paint 55800; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 74 ± 2% |
|---|---|
| Dry Film Thickness | 100 µm |
| Theoretical Spreading Rate | 7.4 m²/L |
| VOC | 232 g/L (China) |
| Density / Specific Gravity | 1.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 26°C |
| Thinner | HEMPEL's Thinner 08450 |
| Colour / Appearance | White 10000 |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
55800
HEMPEL Multi-purpose Epoxy Paint 55800 is a high solids epoxy topcoat whose tough film resists attack by seawater and mineral oils. It provides good gloss and colour retention.
It may be used as a single coat on internal structures of engine rooms and accommodation spaces. It may also be used as a general decorative topcoat. In addition, it may serve as a tie coat between a general primer and a polyurethane topcoat to extend the overcoating interval. The product may also serve as a primer for outfitting components on various substrates, offering workable recoat intervals suited to most newbuilding schedules.
- When used as part of the specified coating system, it is approved as a low flame-spread material. For further details, see the Declaration of Conformity at hempel.com.
| Product safety | Flash point 26 °C |
|---|
| Regulations | Value |
| European Union | 232 g/L |
| USA (coatings) | 245 g/L |
| USA (regulatory) | 245 g/L |
| Canada | 245 g/L |
| China | 232 g/L |
| Hong Kong | 245 g/L |
| South Korea | 232 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 55800 |
|---|---|
| Product components | Base 55809 |
Curing agent 97610
| Standard colour / code | White 10000 |
|---|---|
| Gloss | Semi-gloss |
| Volume solids | 74 ± 2% |
55800
| density | 1.4 kg/L |
|---|---|
| Recommended dry film thickness | 100 µm |
Avoid polishing.
- Before final painting, all shop primer breakdown and contamination incurred during storage and erection must be thoroughly cleaned by mechanical/chemical means.
- Clean thoroughly by hand or power tools to St 3 (ISO 8501-1) / SP 3 (SSPC). Avoid polishing.
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 55809 : curing agent 97610 (4 : 1 by volume)
Stir thoroughly before use.
| Thinner | HEMPEL's Thinner 08450 |
|---|---|
| Cleaning solvent | HEMPEL's Tool Cleaner 99610 |
| Product temperature | 20°C |
|---|---|
| Pot Life | 2 h |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 5% | Nozzle pressure: 15 MPa Nozzle tip size: 0.46-0.53 mm |
| Air Spray | 15% | Nozzle tip size: 0.46 mm |
| Brush/roller | 5% | Nozzle size: 0.53 mm |
If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 75 µm | 250 µm | 100 µm |
| Wet Film Thickness | 101 µm | 338 µm | 135 µm |
| Theoretical Spreading Rate | 10 m²/L | 3 m²/L | 7.4 m²/L |
| Surface temperature | -10°C | 0°C | 10°C | 20°C |
| Surface Dry | 6 h | 4 | 2¼ | 1½ |
| Through dry | 39 h | 19 | 12 | 3 |
| Fully cured | - days | - | 7 | |
55800
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 0°C | 10°C | 20°C | 30°C | |
| Atmospheric, moderate | |||||
|---|---|---|---|---|---|
| HEMPEL Multifunctional Epoxy 55800 | Minimum | 16 h | 7 h | 3½ h | 2½ h |
| Maximum | Extendable* | ||||
| Atmospheric, severe | |||||
| HEMPEL Multifunctional Epoxy 55800 | Minimum | 16 h | 7 h | 3½ h | 2½ h |
| Maximum | Extendable* | ||||
Extendable* Depending on the actual exposure conditions, the coated surface may be recoated after an extended time. Contact your local Hempel representative for advice.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 24 months |
| Curing agent | 24 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 7.6 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
- Application methods. This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
