Hempel's Polyurethane High-build Topcoat 5561B is a polyurethane coating used as a topcoat. Hempel's Polyurethane High-build Topcoat 5561B is recommended as a VOC-compliant topcoat providing effective protection for structural steel in corrosive environments. Hempel's Polyurethane High-build Topcoat 5561B is a glossy polyurethane topcoat cured with aliphatic isocyanate. Parameters on this page: volume solids 61 ± 2%, dry film thickness 60 µm, theoretical spreading rate 10 m²/L. Comparable products from the same brand: Hempel's Polyurethane High-build Topcoat 55610, Hempel's Polyurethane High-build Topcoat 55613, Hempel's Polyurethane Matt Topcoat 552C0.
Source: HEMPEL original technical data sheet (TDS) "Hempel's Polyurethane High-build Topcoat 5561B"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 61 ± 2% |
|---|---|
| Dry Film Thickness | 60 µm |
| Theoretical Spreading Rate | 10 m²/L |
| VOC | 368 g/L (China) |
| Density / Specific Gravity | 1.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 40°C |
| Thinner | HEMPEL's Thinner 08080 |
| Colour / Appearance | Light Grey 11150 ** |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
5561B
Hempel's Polyurethane High-build Topcoat 5561B is a glossy polyurethane topcoat cured with aliphatic isocyanate. The product has excellent gloss and colour retention.
Hempel's Polyurethane High-build Topcoat 5561B is recommended as a VOC-compliant topcoat providing effective protection for structural steel in corrosive environments.
| Product safety | Flash point 40 °C |
|---|
| Regulations | Value |
| European Union | 368 g/L |
| USA (coatings) | 368 g/L |
| USA (regulatory) | 368 g/L |
| Canada | 368 g/L |
| China | 368 g/L |
| Hong Kong | 368 g/L |
| South Korea | 368 g/L |
VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 5561B |
|---|---|
| Product components | Base 5561P |
Curing agent 97050
| Standard colour* / code | Light Grey 11150 ** |
|---|
Light Grey 11150
| Gloss | |
|---|---|
| Volume solids | 61 ± 2% |
| density | 1.4 kg/L |
| Recommended dry film thickness | 60 µm |
_______________________________
| Aluminium colour / code | Aluminium Grey 19871 |
|---|
Refer to the Hempel Guide for Aluminium-containing Coatings.
| Volume solids | 56 ± 2% |
|---|---|
| density | 1.2 kg/L |
| Recommended dry film thickness | 60 µm |
5561B
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 5561P : curing agent 97050 (7 : 1 by volume)
Stir thoroughly before use.
| Thinner | HEMPEL's Thinner 08080 |
|---|---|
| Cleaning solvent | HEMPEL's Thinner 08080 |
| Product temperature | 20°C | 10°C | 30°C |
| Pot Life | 60 min | 90 min | 30 min |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 5% | Nozzle pressure: 17.5 MPa; nozzle size: 0.43–0.53 mm |
| Brush | 5% | Not applicable. |
Hempel's Roller/Brush Additive 99140 may be used to improve levelling. Consult Hempel for advice.
If brush or roller application is used, multiple coats are required to achieve the specified dry film thickness. Never thin beyond the range permitted by local environmental regulations. Spray parameters are indicative and may be adjusted to site conditions. Pressure figures apply to material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 50 µm | 80 µm | 60 µm |
| Wet Film Thickness | 82 µm | 132 µm | 99 µm |
| Theoretical Spreading Rate | 12 m²/L | 7.6 m²/L | 10 m²/L |
Depending on the end use and service area, the product may be specified at film thicknesses other than those indicated. This will alter the spreading rate, drying and curing times and recoat interval. To achieve optimum performance, avoid excessive film thickness.
— During and for a period after application, film formation may be adversely affected by light rain, high humidity and/or condensation: "8 h, 20 °C/68 °F".
5561B
| Surface temperature | -10°C | 0°C | 20°C | 40°C |
| Surface Dry | 2½ h | 1½ | ½ | ¼ |
| Hard Dry | 10 h | 6 | 2 | ½ |
Measured at 60 µm dry film thickness under standard conditions; see Hempel's explanatory notes.
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | -10°C | 0°C | 20°C | 40°C | |
| Atmospheric, moderate | |||||
|---|---|---|---|---|---|
| HEMPEL's Polyurethane Mastic Topcoat 5561B | Minimum | 30 h | 18 h | 6 h | 100 min |
| Maximum | No maximum | ||||
For products of the same generic chemical composition, recoat times are for reference only.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 36 months |
| Curing agent | 24 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 7.6 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
5561B
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
