As a heavy-duty anti-corrosion coating layer, for areas exposed to abrasion and aggressive corrosive environments, such as hatch coamings and cargo holds of bulk carriers. It is designed to withstand the severe conditions of cargo holds and, owing to excellent abrasion resistance, impact resistance, crack resistance and chemical resistance, can effectively reduce contamination. Parameters on this page: volume solids 76 ± 2%, DFT 125 µm, theoretical spreading rate 6.1 m²/L. Comparable products from the same brand: HEMPEL Non-slip Sand 67520, HEMPEL Gas Pipe Coating 87633, HEMPEL Silicone Aluminium Paint 56910.
Parameter source: HEMPEL original technical data sheet (TDS) "HEMPEL Easy-Clean Cargo Hold Coating"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 76 ± 2% |
|---|---|
| Dry Film Thickness | 125 µm |
| Theoretical Spreading Rate | 6.1 m²/L |
| VOC | 254 g/L (China) |
| Density / Specific Gravity | 1.5 kg/L |
| Number of Components | Two-component |
| Flash Point | 25°C |
| Thinner | HEMPEL's Thinner 08450 |
| Colour / Appearance | Venetian Red 50630 * |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
HEMPEL CargoHold Easy Clean is a two-component, high-build pure epoxy paint used as the final coat for cargo holds to facilitate cleaning.
It is designed to withstand the harsh conditions of cargo holds and, due to excellent abrasion resistance, impact resistance, crack resistance and chemical resistance, effectively reduces contamination.
It can be applied at surface temperatures as low as -5 °C/22 °F and cures rapidly, ensuring quick return to service after application.
As a heavy-duty anti-corrosion coating layer, for areas exposed to wear and aggressive corrosive environments, such as hatch coamings and cargo holds of bulk carriers.
This product is not recommended for new construction projects.
| Product safety | Flash point 25 °C |
|---|
| Regulations | Value |
| European Union | 254 g/L |
| USA (coatings) | 254 g/L |
| USA (regulatory) | 254 g/L |
| China | 254 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 47900 |
|---|---|
| Product components | Base 47909 |
Curing Agent 98510
| Standard colour / code | Venetian Red 50630 * |
|---|
Brown-red 50630
| Gloss | Semi-gloss |
|---|---|
| Volume solids | 76 ± 2% |
| density | 1.5 kg/L |
| Recommended dry film thickness | 125 µm |
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 47909 : Curing Agent 98510 (3 : 1 by volume)
Stir thoroughly before use.
| Thinner | HEMPEL's Thinner 08450 |
|---|---|
| Cleaning solvent | HEMPEL's Tool Cleaner 99610 |
| Product temperature | 20°C | 15°C | 25°C |
| Pot Life | 60 min | 90 min | 50 min |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 5% | Nozzle pressure: 25 MPa; nozzle size: 0.53–0.64 mm |
| Brush/roller | 5% | Not applicable. |
The product requires heavy-duty spray equipment; the spray hose should be as short as possible. To reduce dry spray at high temperatures, additional thinning may be required. Spray parameters are indicative and may be adjusted according to site conditions. Pressure values apply to the material at 20 °C. (*Consult our representative if other application methods are required!).
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 125 µm | 175 µm | 125 µm |
| Wet Film Thickness | 165 µm | 230 µm | 165 µm |
| Theoretical Spreading Rate | 6.1 m²/L | 4.3 m²/L | 6.1 m²/L |
To achieve optimum performance, avoid excessive film thickness.
- Previous coat: Recommended products: Hempadur Easy 47700, Hempadur Ultra-Strength Fibre 47510 - Subsequent coat: None or according to Hempel's specification.
| Surface temperature | -5°C | 0°C | 20°C | 30°C |
| Touch Dry | 12 h | 8 | 2½ | 1½ |
| Hard Dry | 24 h | 15 | 4 | 2½ |
| Fully cured | 14 days | 10 | 2 | - |
Measured at 125 µm dry film thickness under standard conditions; see Hempel's explanatory notes.
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 0°C | 10°C | 20°C | 30°C | |
| Atmospheric, severe | |||||
|---|---|---|---|---|---|
| HEMPEL's Easy-clean Cargo Hold Coating | Minimum | 5 min | |||
| Maximum | 24 h | 10 h | 7 h | ||
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
If the product requires overcoating with itself, the second coat shall be applied before the first coat dries (wet-on-wet).
| Ambient temperature | 25°C |
| Binder | 18 months |
| Curing agent | 24 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 7.1 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
