HEMPEL Acrylic Thick Coat 4641S belongs to acrylic coatings. 2. This product may be used as its own primer for repair and touch-up of container coating systems, and also for other repair situations requiring an economical and rapid solution. Its film is resistant to seawater, aliphatic solvents and splashes of animal and vegetable oils. Parameters on this page: volume solids 43 ± 2%, dry film thickness 100 µm, theoretical spreading rate 4.3 m²/L. Comparable models from the same brand: HEMPEL Pure Acrylic Road Marking Paint 29680, HEMPEL Acrylic Thick Coat 46410, HEMPEL Acrylic Thick Coat 4641C.
Parameter source: HEMPEL original technical data sheet (TDS) “HEMPEL Acrylic Thick Coat 4641S”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 43 ± 2% |
|---|---|
| Dry Film Thickness | 100 µm |
| Theoretical Spreading Rate | 4.3 m²/L |
| VOC | 501 g/L (China) |
| Density / Specific Gravity | 1.3 kg/L |
| Number of Components | — |
| Flash Point | 23°C |
| Thinner | HEMPEL's Thinner 08080 |
| Colour / Appearance | Tan camouflage 25810 ** |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
4641S
HEMPEL Acrylic Thick Coat 4641S is a physically drying high-build coating based on acrylic resin, with a non-chlorinated plasticizer and zinc phosphate slow-release pigment, and exhibits good colour retention when used as a flat topcoat. Its film is resistant to seawater, aliphatic solvents and splashes of animal and vegetable oils.
1. May be used as primer, intermediate coat and topcoat in chlorinated rubber or acrylic systems for medium-corrosive environments. 2. This product may be used as its own primer for repair and touch-up of container coating systems, and also for other repair situations requiring an economical and rapid solution. 3. May be used as container topcoat.
| Product safety | Flash point 23 °C |
|---|
| Regulations | Value |
| European Union | 501 g/L |
| USA (coatings) | 501 g/L |
| USA (regulatory) | 501 g/L |
| China | 501 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 4641S |
|---|---|
| Standard colour* / code | Tan camouflage 25810 ** |
Beige 25810
| Gloss | Flat |
|---|---|
| Volume solids | 43 ± 2% |
| density | 1.3 kg/L |
| Recommended dry film thickness | 100 µm |
For further details, refer to the separate Hempel document Surface Preparation Guide.
Stir thoroughly before use.
| Thinner | HEMPEL's Thinner 08080 |
|---|
4641S
| Cleaning solvent | HEMPEL's Thinner 08080 |
|---|
| Tools | Application parameters |
|---|
Nozzle pressure: 17.5 MPa
Tip size: 0.43–0.53 mm. If brush or roller application is used, multiple coats are required to achieve the specified dry film thickness. Spray parameters are indicative and may be adjusted to site conditions. Pressure figures apply to material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Wet Film Thickness | 174 µm | 291 µm | 232 µm |
| Theoretical Spreading Rate | 5.7 m²/L | 3.4 m²/L | 4.3 m²/L |
Depending on the end use and service area, the product may be specified at film thicknesses other than those indicated. This will alter the spreading rate, drying and curing times and recoat interval. To achieve optimum performance, avoid excessive film thickness.
| Surface temperature | 20°C |
| Surface Dry | 45 min |
| Through dry | 90 min |
| Fully cured | 7 days |
Measured at 100 µm dry film thickness under standard conditions; see Hempel's explanatory notes.
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
|---|---|
| Product | 60 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
4641S
| GWP (Global Warming Potential) | 8.4 g CO₂e/m² |
|---|
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
