Hempel Rapid Epoxy 45410 is an epoxy paint. Used as a topcoat in environments where the normal appearance of epoxy coatings is acceptable. Complies with EU Directive 2004/42/EC "Directive on the limitation of volatile organic compounds in paints: Subcategory j". Parameters on this page: volume solids 65 ± 2%, dry film thickness 80 µm, theoretical spreading rate 8.1 m²/L. Comparable models of the same brand and type: Hempel Fibre Reinforced Epoxy 47510, Hempel Multi-purpose Epoxy High Build 500 Winter Grade, Hempel Multi-purpose Epoxy High Build 500.
Parameter source: HEMPEL original technical data sheet (TDS) “Hempel Rapid Epoxy 45410”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 65 ± 2% |
|---|---|
| Dry Film Thickness | 80 µm |
| Theoretical Spreading Rate | 8.1 m²/L |
| VOC | 332 g/L (China) |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Flash Point | 26°C |
| Thinner | HEMPEL's Thinner 08450 |
| Colour / Appearance | Limestone Grey 12170 |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
45410
Hempel Rapid Epoxy 45410 is a two-component high-solids epoxy paint. The product forms a hard film resistant to seawater, mineral oils, and splashes of petrol and related products. Coloured with zinc phosphate.
Complies with EU Directive 2004/42/EC, the Paints Directive on limiting volatile organic compounds: subcategory j.
Used as a fast-curing topcoat in moderately to severely corrosive environments.
Applied directly to metal surfaces in moderately corrosive environments.
Used as a topcoat in environments where the normal appearance of epoxy coatings is acceptable.
| Product safety | Flash point 26 °C |
|---|
| Regulations | Value |
| European Union | 332 g/L |
| USA (coatings) | 332 g/L |
| USA (regulatory) | 332 g/L |
| Canada | 332 g/L |
| China | 332 g/L |
| Hong Kong | 332 g/L |
| South Korea | 332 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. ªEU Directive 2004/42/CE. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 45410 |
|---|---|
| Product components | Base 45419 |
Curing agent 98430_______________________________
| Standard colour / code | Limestone Grey 12170 |
|---|
Light grey 12170; other colours available through the company's tinting system
| Gloss | Semi-flat |
|---|---|
| Volume solids | 65 ± 2% |
1.4 kg/L
| Recommended dry film thickness | 80 µm |
|---|
_______________________________
| Aluminium colour / code | Aluminium 19000 |
|---|
Aluminium Grey 19000
45410
| Volume solids | 62 ± 2% |
|---|
1.3 kg/L
| Recommended dry film thickness | 80 µm |
|---|
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 45419 : Curing agent 98430 (3 : 1 by volume)
Stir thoroughly before use.
| Thinner | HEMPEL's Thinner 08450 |
|---|---|
| Cleaning solvent | HEMPEL's Tool Cleaner 99610 |
| Product temperature | 20°C |
| Pot Life | 90 min |
| Pot life (spray) | 90 min |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 10% | Nozzle pressure: 25 MPa Nozzle tip size: 0.46–0.53 mm |
| Air Spray | 35% | Not applicable. |
| Brush | 10% | Not applicable. |
If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 80 µm | 125 µm | 80 µm |
| Wet Film Thickness | 123 µm | 192 µm | 123 µm |
| Theoretical Spreading Rate | 8.1 m²/L | 5.2 m²/L | 8.1 m²/L |
Depending on the application and service area, the product may be specified at film thicknesses other than those indicated. This will change the spreading rate, drying and curing times and recoating intervals. To obtain optimal performance, avoid excessive film thickness. Over-application must be strictly controlled; locally the DFT must never exceed 250 µm [10 mil]. On irregular surfaces, particular care is recommended to avoid over-application.
45410
- Previous coat: None or according to Hempel's specification. Recommended products: Hempel Rapid Epoxy 17410, Hempel Zinc-rich Epoxy Primer 17360 - Subsequent coat: None or according to Hempel's specification. Recommended product: Polyurethane topcoat
| Surface temperature | 20°C |
| Touch Dry | 60 min |
| Hard Dry | 120 min |
Measured at 80 µm dry film thickness under standard conditions; see Hempel's explanatory notes.
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 0°C | 10°C | 20°C | |
| Atmospheric, moderate | ||||
|---|---|---|---|---|
| HEMPEL's Fast-drying Epoxy 45410 | Minimum | 9 h | 4 h | 2 h |
| Maximum | 90 days | 60 days | 30 days | |
| HEMPEL's Polyurethane Mastic Topcoat 55610 | Minimum | 9 h | 4 h | 2 h |
| Maximum | 90 days | 60 days | 30 days | |
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 36 months |
| Curing agent | 36 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 8.1 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
45410
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
