Hempel Ultra-strength Epoxy Paint 35530 is an epoxy paint. Used as a high-performance coating for steel plate surfaces where colour retention is not important, abrasion is severe and solvent-free properties are required. Hempel Ultra-strength Epoxy Paint 35530 is a two-component solvent-free, high-build, polyamine-cured epoxy coating; the cured film has good resistance to fresh water, seawater, crude oil and abrasion. Parameters on this page: volume solids 100%, dry film thickness 300 µm, theoretical spreading rate 3.3 m²/L. Comparable products of the same brand: Hempel Fibre-reinforced Extra-strong Epoxy Paint 47510, Hempel Multi-purpose Epoxy High-build Paint 500 Winter Type, Hempel Multi-purpose Epoxy High-build Paint 500.
Data source: HEMPEL original Technical Data Sheet (TDS), "Hempel Ultra-strength Epoxy Paint 35530"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 100% |
|---|---|
| Dry Film Thickness | 300 µm |
| Theoretical Spreading Rate | 3.3 m²/L |
| VOC | 10 g/L (China) |
| Density / Specific Gravity | 1.3 kg/L |
| Number of Components | Two-component |
| Flash Point | 138°C |
| Gloss | Semi-gloss |
| Pot Life | 60 min |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
35530
Hempel Ultra-strength Epoxy Paint 35530 is a two-component solvent-free, high-build, polyamine-cured epoxy coating; the cured film has good resistance to fresh water, seawater, crude oil and abrasion. This product can be applied in high build with standard high-performance airless spray equipment. This product is harmless to grain.
Used as a high-performance coating for steel plate surfaces where colour retention is not important, abrasion is severe and solvent-free properties are required. If solvent-borne paint is permitted, Hempel Ultra-strength Epoxy Paint 45751 can be used instead. For use as a potable water tank lining, refer to the relevant certificates. For use in mild environments, see the application guide.
search=Hempel&page=0.
| Product safety | Flash point 138 °C |
|---|
| Regulations | Value |
| European Union | 10 g/L |
| USA (coatings) | 10 g/L |
| USA (regulatory) | 10 g/L |
| Canada | 10 g/L |
| China | 10 g/L |
| Hong Kong | 10 g/L |
| South Korea | 10 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 35530 |
|---|---|
| Product components | Base 35539 |
Hardener 95530
Light grey 10500 *
| Gloss | Semi-gloss |
|---|---|
| Volume solids | 100% |
35530
| density | 1.3 kg/L |
|---|---|
| Recommended dry film thickness | 300 µm |
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 35539 : Hardener 95530 (3 : 1 by volume)
Mix each component thoroughly before combining the components. Stir thoroughly before use.
| Cleaning solvent | HEMPEL's Tool Cleaner 99610 |
|---|
| Product temperature | 20°C |
|---|---|
| Pot Life | 60 min |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 0% | Nozzle pressure: 25 MPa; tip size: 0.48–0.79 mm |
| Brush | 0% | Not applicable. |
If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. For tank linings, brush and roller application must be limited to touch-up, repair areas or minor repairs. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 200 µm | 500 µm | 300 µm |
| Wet Film Thickness | 200 µm | 499 µm | 300 µm |
| Theoretical Spreading Rate | 5 m²/L | 2 m²/L | 3.3 m²/L |
To achieve optimum performance, avoid excessive film thickness. Depending on the end use and service area, the product may be specified at film thicknesses other than those indicated. This will alter the spreading rate, drying and curing times and recoat interval.
35530
- Preceding coats: none or according to Hempel's specification. Recommended products: Hempel Epoxy Sealer 05990, Hempel Epoxy Paint 15590 - Subsequent coats: none or according to Hempel's specification. Recommended products: Hempel Epoxy
coating, polyurethane topcoat
| Surface temperature | 20°C |
| Touch Dry | 6 h |
| Hard Dry | 15 h |
| Fully cured | 7 days |
Dry film thickness 300 µm measured under standard conditions; see Hempel's explanatory notes for details.
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 10°C | 20°C | 30°C | |
| Atmospheric, moderate | ||||
|---|---|---|---|---|
| HEMPEL High-Strength Epoxy 35530 | Minimum | 40 h | 16 h | 8 h |
| Maximum | 12 days | 5 days | 60 h | |
| Immersion | ||||
| HEMPEL High-Strength Epoxy 35530 | Minimum | 40 h | 16 h | 8 h |
| Maximum | 12 days | 5 days | 60 h | |
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- For tank linings, if the maximum recoat interval is exceeded, roughen the surface by blasting to ensure intercoat adhesion.
| Ambient temperature | 25°C |
| Binder | 36 months |
| Curing agent | 24 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with local law at temperatures not exceeding 40 °C [104 °F], away from direct sunlight and direct exposure to rain or snow.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 7 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
35530
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
