Hempel Epoxy Shop Primer 15275 is an epoxy paint for use as a primer. It provides protection for blast-cleaned steel plates and other steel structures during storage and construction. Hempel Epoxy Shop Primer 15275 is a two-component polyamide-cured epoxy shop primer containing zinc phosphate anti-corrosive pigment. Parameters on this page: volume solids 26 ± 2%, dry film thickness 20 µm, theoretical spreading rate 13 m²/L. Comparable models from the same brand: Hempel Epoxy Primer 1530C, Hempel Epoxy Primer 158CN, Hempel Epoxy Shop Primer 15280.
Parameter source: HEMPEL original technical data sheet (TDS) “Hempel Epoxy Shop Primer 15275”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 26 ± 2% |
|---|---|
| Dry Film Thickness | 20 µm |
| Theoretical Spreading Rate | 13 m²/L |
| VOC | 642 g/L (China) |
| Density / Specific Gravity | 1.2 kg/L |
| Number of Components | Two-component |
| Flash Point | 4°C |
| Thinner | HEMPEL's Thinner 08570 |
| Colour / Appearance | Brown-red 50890 |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
15275
Hempel Epoxy Shop Primer 15275 is a two-component polyamide-cured epoxy shop primer containing zinc phosphate anti-corrosive pigment. Designed for automatic spray application.
Provides protection for blast-cleaned steel plates and other steel structures during storage and construction.
- Reaction-to-fire tested in accordance with EN 13501-1 (as part of a coating system using approved primer and topcoat). B-s1, d0.
| Product safety | Flash point 4 °C |
|---|
| Regulations | Value |
| European Union | 642 g/L |
| USA (coatings) | 642 g/L |
| USA (regulatory) | 642 g/L |
| Canada | 642 g/L |
| China | 642 g/L |
| Hong Kong | 642 g/L |
| South Korea | 642 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. VOC values may vary with colour; refer to Section 9 of the Safety Data Sheet. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 15275 |
|---|---|
| Product components | Base 15274 |
Curing agent 95175
| Standard colour* / code | Brown-red 50890 |
|---|---|
| Gloss | Flat |
| Volume solids | 26 ± 2% |
| density | 1.2 kg/L |
| Recommended dry film thickness | 20 µm |
15275
Base 15274 : Curing agent 95175 (65 : 35 by volume)
Stir thoroughly before use.
| Thinner | HEMPEL's Thinner 08570 |
|---|---|
| Cleaning solvent | HEMPEL's Tool Cleaner 99610 |
| Product temperature | 20°C |
|---|---|
| Pot Life | 72 h |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 20% | Nozzle pressure: 7.5 MPa Nozzle tip size: 0.53 mm |
| Air Spray | 20% | Not applicable. |
| Brush | 20% | Not applicable. |
Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Wet Film Thickness | 58 µm | 96 µm | 77 µm |
| Theoretical Spreading Rate | 17 m²/L | 10 m²/L | 13 m²/L |
| Surface temperature | 20°C |
| Dry to handle | 6 min |
| Fully cured | 7 days |
Dry film thickness 20 µm measured under standard conditions; see Hempel's explanatory notes for details.
Hempel's specifications supersede all guidance shown in the recoat table.
| Product name | 20°C | |
| Atmospheric, moderate | ||
|---|---|---|
| Hempadur 15571 | Minimum | 6 h |
| Maximum | No maximum | |
For products of the same generic chemical composition, recoat times are for reference only.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 24 months |
| Curing agent | 36 months |
15275
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| GWP (Global Warming Potential) | 16.3 g CO₂e/m² |
|---|
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
