5843A SEAFLO NEO SL Tin-Free Self-Polishing Antifouling is an antifouling. SEAFLO NEO SL is a high-performance hydrolysing antifouling based on silyl polymer, providing long-lasting antifouling performance, low friction resistance and low energy consumption. Parameters on this page: volume solids 55 ± 2% (by volume), dry film thickness 75-165 µm, theoretical spreading rate 0.136-0.3 L/m². Comparable models from the same brand: 4010B SEATENDER 7 tin-free self-polishing antifouling, 5843H SEAFLO NEO SL Z tin-free self-polishing antifouling, 5843K SEAFLO NEO tin-free self-polishing antifouling.
Data source: CMP original Technical Data Sheet (TDS), "5843A SEAFLO NEO SL Tin-free Self-polishing Antifouling Paint"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 55 ± 2% (by volume) |
|---|---|
| Dry Film Thickness | 75–165 µm |
| Theoretical Spreading Rate | 0.136-0.3 L/m2 |
| VOC | 408 g/L |
| Density / Specific Gravity | 1.87 g/ml |
| Number of Components | One-component |
| Flash Point | 27°C |
| Thinner | CR/ACRI THINNER A |
| Colour / Appearance | Brown, light brown, blue |
SEAFLO NEO SL is a high-performance hydrolysable antifouling based on silane polymer, providing long-term antifouling performance, low frictional resistance and low energy consumption.
SEAFLO NEO SL has a higher solids content than conventional hydrolysable coatings.
| Type | Tin-free self-polishing antifouling |
|---|---|
| Use | Suitable as a bottom antifouling for ocean-going steel ships to extend docking intervals. |
| Colour | Brown, light brown, blue |
|---|---|
| Flash Point | 27°C |
| Density | 1.87 g/ml |
| Volume Solids | 55 ± 2% (by volume) |
| Volatile organic compound content | 408 g/L |
| Theoretical spreading rate | 0.136-0.3 L/m2 |
| Thickness | Wet film 136–300 µm, dry film 75–165 µm |
(dry film 100 µm)
| Temperature | -5 °C | 0 °C | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 8 h | 5 h | 3 h | 2 h | 1 h | 30 min |
| Hard Dry | 22 h | 16 h | 12 h | 8 h | 5 h | 4 h | |
| Recoat interval | At least | 22 h | 16 h | 12 h | 8 h | 5 h | 4 h |
| At most | / | / | / | ||||
| Dry-to-launch time | Fastest | 48 h | 36 h | 24 h | 18 h | 12 h | 10 h |
| Application method | Airless spray, brush, roller |
|---|---|
| Weather: temperature | Minimum -5 °C |
| Humidity | Maximum 85% RH; steel temperature at least 3 °C above the dew point |
| Airless spray: viscosity | 1.5-2.5Pa·s |
| Nozzle | (Graco)621-723 |
| Paint output pressure | 11.7-14.7MPa |
| Spray gun speed | 60–80 cm/s |
| Thinner | CR/ACRI THINNER A |
| Thinning | 0–7% by volume |
| Preceding coat | BANNOH 500 N, BANNOH 500 R, BANNOH 500 S, SILVAX SQ-K, CMP AC, CMP AC-10, BANNOH 1500 N, BANNOH 1500 S, etc. |
| Subsequent coat | - |
| Packaging | One-component |
Note: 1. If a ship berths continuously for two weeks or longer, especially in areas at risk of heavy marine growth, the bottom antifouling areas may be fouled by marine organisms.
2. Maintain ventilation from application until full cure to remove residual solvent and promote curing.
3. Stir with a mixer until homogeneous, then add the appropriate thinner and mix.
4. Below 10 °C, additional thinner may be required to obtain a suitable application viscosity.
5. Excessive thinning, however, reduces sag resistance and film performance.
6. Slight colour change may occur after immersion and outdoor exposure.
7. Density, solids content and VOC content are theoretical calculated values for a typical colour (brown), based on the formulation without added thinner. Values vary between colours.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
