Heat-reflective Thermal Insulation Coating XH6405R belongs to Thermal Insulation coatings. A high-solids two-component synthetic resin coating formulated with functional pigments, fillers and additives, suitable for heat-reflective, thermal-insulating and weather-resistant coatings on tanks and other facilities under severe atmospheric corrosive environments. Parameters on this page: Volume Solids 65 ± 2%, Dry Film Thickness (DFT) 60/80/100 µm, Theoretical Spreading Rate 6.5 m²/L.
Parameter source: T&H original technical data sheet (TDS) for Heat-reflective Thermal Insulation Coating XH6405R; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 65 ± 2% |
|---|---|
| Dry Film Thickness | 60/80/100 µm |
| Theoretical Spreading Rate | 6.5 m2/L |
| VOC | 340g/L |
| Density / Specific Gravity | 1.45 kg/L |
| Number of Components | Two-component |
| Flash Point | 25°C |
| Thinner | 0-20% |
| Mixing Ratio | Base : curing agent = 10:1 (by weight), 88:12 (by volume) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A high-solids two-component synthetic resin coating formulated with functional pigments, fillers and additives, suitable for heat-reflective, thermal-insulating and weather-resistant coatings on tanks and other facilities under severe atmospheric corrosive environments.
| Colour | Pure white only |
|---|---|
| Gloss | |
| density | 1.45 kg/L |
| Volume Solids | 65±2% |
| Volatile Organic Compounds | 340g/L |
| Flash Point | 25°C |
| Mixing ratio | Base : curing agent = 10:1 (by weight), 88:12 (by volume) |
| Typical dry film thickness | 60µm |
|---|---|
| Recommended dry film thickness | 50–100 µm, depending on system requirements |
| Induction time (20 °C) | 10-15min |
| Thinner quantity (by volume) | Airless spray 5–15% | Air spray 15–30% | Roller or brush 0–20% |
| Recommended nozzle size | 0.38~0.53mm | 1.5~2.5mm | None |
| Recommended spray pressure | 15~20MPa | 0.3~0.6MPa | None |
| Application suitability | Recommended | Applicable | Suitable for small-area repair |
*Select a suitable thinner according to the season and temperature
| Dry film thickness (µm) | 60 | 80 | 100 |
| Wet film thickness (µm) | 92 | 123 | 154 |
| Theoretical spreading rate (m²/L) | 10.8 | 8.2 | 6.5 |
| Temperature | Surface Dry | Hard Dry | Pot Life | Recoat interval | |
| Minimum | Maximum* | ||||
| 5°C | 5h | 24h | 6h | 24h | |
| 15°C | 150min | 18h | 4h | 18h | / |
| 25°C | 90min | 12h | 2h | 12h | |
| 40°C | 60min | 8h | 45min | 8h | |
*The maximum recoat interval depends on the exposure environment and the end use of the coating.
All surfaces to be coated shall be clean, dry and free from contamination. Before application, all surfaces shall be assessed and prepared in accordance with ISO 8504:2000. The product shall be applied over the recommended anticorrosive primer or intermediate coat within the specified overcoating interval; the primer or intermediate coat surface shall be dry and free from contamination. When applied over existing coatings, chalk, grease and other contaminants shall be removed by appropriate methods. In cracked or damaged areas, the substrate shall be prepared to Sa2½ or St3 and the primer repaired before applying this product.
1. Ensure ventilation and air exhaust during application, keep away from ignition sources, and wear protective equipment such as masks and gloves; maintain adequate ventilation during curing. 2. When mixing, first stir the base uniformly, then add the hardener at the specified ratio and mix uniformly; adjust the thinner amount according to application needs and temperature changes, stir thoroughly and allow to induce. 3. Over-thinning will reduce sag resistance and slow curing. 4. Excessive coating thickness will seriously affect drying and curing, recoatability and handling time. 5. After long-term exposure of the coating, ensure the old film surface is free of contaminants before recoating, and sand the surface before applying subsequent coatings. 6. Brush or roller application cannot achieve high film thickness and a good continuous film in a single coat; multiple coats are required. 7. This product prepared with relatively bright chrome-free red or yellow pigments requires multiple coats to achieve good hiding power when applied over dark primers; therefore light-coloured primers or intermediate coats are recommended when using these colours. 8. During application and curing, the substrate temperature must be above 5°C and at least 3°C above the dew point, and relative humidity must not exceed 85%. 9. Cutting structures coated with this coating generates fumes and dust; appropriate protection shall be provided. 10. When work is suspended, do not leave coating in paint lines, spray guns or spray equipment. Thoroughly flush all equipment with thinner. If the suspension is prolonged, it is recommended to mix a fresh batch of paint for application. 11. All equipment shall be cleaned with thinner immediately after use. Periodic flushing of spray equipment during daily work is good practice. Cleaning frequency depends on spray volume, temperature, spray time, including interruption time and other factors. 12. Residual paint and empty containers shall be disposed of in accordance with relevant regional regulations.
| 22 kg per unit | Base 20 kg | Curing agent 2 kg |
| 15 L per unit | Base 13.2 L | Curing agent 1.8 L |
Keep sealed in a ventilated, cool, dry place away from sources of ignition. Minimum 12 months.
1. For the coating and its recommended thinners, see the safety sheets and the safety data of the relevant materials. This is a solvent-borne coating; avoid inhaling spray mist and solvent vapours, and avoid exposing skin and eyes and contact with uncured paint as far as possible. 2. All work related to the application and use of this product must comply with the relevant national health, safety and environmental standards and regulations. 3. If welding or flame cutting is required on metal coated with this product, dust and fumes will be generated; use appropriate personal protective equipment and adequate local ventilation. 4. If in doubt about the suitability of this product, consult the company.
The information provided in this datasheet is based on laboratory test results believed to be accurate and is for application guidance only. All advice and recommendations of T&H regarding the use of T&H products, whether in technical documents, specific consultations or otherwise, are based on information believed to be the most reliable. Our products and the information provided are intended for users with the necessary knowledge and industrial experience, and the end customers shall ultimately determine whether these products are suitable for their use. T&H cannot control the quality and condition of substrates, nor the various factors affecting product use. Therefore, T&H assumes no liability for any loss, injury or damage arising from the use of its products or reference to this datasheet (unless otherwise agreed in writing). Datasheet data will be modified as necessary based on practical experience and the need for continuous product development.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
