Acrylic Polyurethane Deck Paint XH6007N

Browse Similar Models by CategoryThis model belongs to: Polyurethane, Acrylic

Product Description

Composed of high-quality acrylic resin, non-yellowing aliphatic polyurethane hardener, high-quality weather-resistant pigment(filler), additives and solvents. Suitable for steel structure surfaces such as ship superstructures, power plants, steel mills, chemical plants and bridges as a high weather-resistant, high-protection topcoat.

Product Characteristics

• Good gloss and colour retention
• Good appearance
• Suitable for most primers and intermediate coats, with excellent intercoat adhesion
• Good long-term recoatability

Basic physical and chemical data

Application parameters

Application Methods

Theoretical Spreading Rate

Application data (typical dry film thickness 60 µm)

*The maximum recoat interval depends on the exposure environment and the end use of the coating.

Surface Preparation

All surfaces to be coated must be clean, dry and free of contaminants. Before application, all surfaces must be assessed and prepared in accordance with ISO 8504:2000. This product must be applied over the recommended anti-corrosive primer or intermediate coat within the specified recoat interval; the primer or intermediate coat must be dry and free of contaminants. When applied over other existing coatings, remove chalk, grease and other contaminants by suitable methods. Substrate in cracked or damaged areas must be prepared to Sa 2½ or St 3 and the primer repaired before applying this product.

Precautions

1. During application, ensure ventilation and exhaust, keep away from sources of ignition, and wear protective equipment such as a mask and gloves; maintain adequate ventilation also during curing. 2. When mixing, first stir the base thoroughly, then add the curing agent in the specified ratio and mix well; adjust the thinner quantity according to application needs and temperature, stir thoroughly and allow induction. 3. Excessive thinning reduces sag resistance and slows curing. 4. Excessive film thickness severely affects drying, curing, recoatability and handling time. 5. Before recoating a coating exposed long-term, ensure the old film is free of contaminants and abrade the surface before applying the next coat. 6. With brush or roller application, high film thickness and a good continuous film cannot be achieved in one coat; several coats are required. 7. Products made with bright chromate-free red or yellow pigments require several coats over dark primers to achieve good hiding; therefore, a light-coloured primer or intermediate coat is recommended with these colours. 8. During application and curing, the substrate temperature must be above 5 °C and at least 3 °C above the dew point, with relative humidity not more than 85%. 9. Cutting of structures coated with this product produces fume; take appropriate protection. 10. When work is interrupted, do not leave paint in hoses, spray guns or spray equipment. Flush all equipment thoroughly with thinner. If the interruption is long, mix a fresh batch of paint for application. 11. Clean all equipment immediately after use with thinner. Flushing spray equipment periodically during daily work is good practice. Cleaning frequency depends on the volume sprayed, temperature, spraying time, including interruptions, and other factors. 12. Surplus paint and empty containers must be disposed of in accordance with the relevant regional regulations.

Packaging

Storage

Keep sealed in a ventilated, cool, dry place away from sources of ignition. Minimum 12 months.

Safety Precautions

1. For the coating and its recommended thinners, see the safety sheets and the safety data of the relevant materials. This is a solvent-borne coating; avoid inhaling spray mist and solvent vapours, and avoid exposing skin and eyes and contact with uncured paint as far as possible. 2. All work related to the application and use of this product must comply with the relevant national health, safety and environmental standards and regulations. 3. If welding or flame cutting is required on metal coated with this product, dust and fumes will be generated; use appropriate personal protective equipment and adequate local ventilation. 4. If in doubt about the suitability of this product, consult the company.

Scope of liability

The information provided in this product data sheet is based on laboratory test results we believe to be accurate, and is for application guidance only. T&H's advice and suggestions on the use of T&H products, whether in technical documents, special consultations or otherwise, are based on information we consider most reliable. Our products and the information provided are intended for users with the requisite knowledge and industrial experience; it is ultimately for these end customers to decide whether the products are suitable for their use. T&H cannot control the quality and condition of the substrate, nor the various factors affecting product use. Therefore, T&H accepts no liability for any loss, injury or damage arising from the use of our products or from reliance on this data sheet (unless otherwise agreed in writing).

Data in this data sheet may be revised as necessary based on practical experience and continuing product development.

Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.