Epoxy Anti-corrosive Primer XH4010S

Browse Similar Models by CategoryThis model belongs to: Primer, Epoxy

Product Description

It is a general-purpose two-component high-build epoxy coating that can be used with a variety of coatings, suitable as an anti-corrosive primer for water-immersion coating systems, and has good adhesion to substrates such as aluminium alloy and aluminium-magnesium alloy.

Product Characteristics

• Good adhesion to substrates such as steel and aluminium alloy
• Good penetration and anticorrosive performance
• Good recoatability
• Wide compatibility
• Good abrasion resistance

Basic physical and chemical data

Application parameters

Application Methods

*Use a slow thinner in hot weather

Theoretical Spreading Rate

Application data (typical dry film thickness 80 µm)

*The maximum recoat interval depends on the exposure environment and the end use of the coating.

Surface Preparation

All surfaces to be coated must be clean, dry and free of contaminants. Before application, all surfaces must be assessed and prepared in accordance with ISO 8504:2000. Abrasive blast clean to Sa 2½, with surface roughness 40–75 µm. Before rust removal, remove all oil and weld spatter and grind welds and sharp edges. Areas of the coating damaged mechanically and showing localised rust must be spot blast cleaned to Sa 2½ or cleaned with power tools to St 3 before local repair. If this coating is to be applied over an approved zinc dust primer old film, thoroughly remove any chalking or zinc salts from the zinc dust coating before applying this product. For concrete protection, the concrete must be cured, with moisture content and surface condition meeting the relevant requirements.

Precautions

1. During application, ensure good ventilation and exhaust, keep away from ignition sources, and wear a mask, gloves and other protective equipment; adequate ventilation shall also be maintained during curing. 2. Before mixing the two components, stir the base thoroughly with a power tool, then add the curing agent and mix uniformly; adjust the thinner amount according to application requirements and temperature changes, mix thoroughly, and allow an induction time of 10–15 min before application. 3. The product may be used as a primer for galvanized steel or stainless steel; abrading or light blasting of these substrates gives better adhesion. 4. When used as a protective primer on concrete, it is normally used with a dedicated concrete sealer. If applied to concrete without a sealer, thin the product to a sufficiently low viscosity (20–30% thinner) and seal the concrete; ensure the sealer is hard dry before overcoating. 5. When used as a tie-coat over inorganic zinc silicate primers, add 20–30% thinner to reduce the viscosity, and ensure the tie-coat is hard dry before applying the next coat, otherwise the effectiveness of sealing pinholes will be reduced. If the product is applied over an old zinc dust primer film, chalk or zinc salts on the zinc dust coating shall be removed thoroughly. 6. The recommended film thickness per coat shall not exceed 120 µm, otherwise the surface smoothness rises and affects overcoating. If the coating chalks after long-term exposure, wash with high-pressure water or abrade the surface before applying the next coat. 7. During application and curing, the substrate temperature shall be above 5 °C and at least 3 °C above the dew point, and the relative humidity shall not exceed 85%. Temperature and relative humidity shall be measured on the substrate close to the work area. 8. Cutting structures coated with this coating produces fumes; appropriate protection shall be taken. 9. When work is interrupted, do not leave paint in hoses, spray guns or spray equipment. Flush all equipment thoroughly with thinner. If work is interrupted for too long, remix a fresh batch of paint before resuming. 10. All equipment shall be cleaned with thinner immediately after use. Periodically flushing spray equipment during the daily work is good practice. The frequency of cleaning depends on the quantity sprayed, temperature, spraying time and interruptions. 11. Remaining paint and empty cans shall be disposed of in accordance with relevant local regulations.

Packaging

Storage

Keep sealed in a ventilated, cool, dry place away from sources of ignition. Minimum 12 months.

Safety Precautions

1. For the coating and its recommended thinners, see the safety sheets and the safety data of the relevant materials. This is a solvent-borne coating; avoid inhaling spray mist and solvent vapours, and avoid exposing skin and eyes and contact with uncured paint as far as possible. 2. All work related to the application and use of this product must comply with the relevant national health, safety and environmental standards and regulations. 3. If welding or flame cutting is required on metal coated with this product, dust and fumes will be generated; use appropriate personal protective equipment and adequate local ventilation. 4. If in doubt about the suitability of this product, consult the company.

Scope of liability

The information provided in this product data sheet is based on laboratory test results that we consider accurate, and is provided for application guidance only. All recommendations and advice given by T&H on the use of T&H products, whether in technical documents, special consultation or otherwise, are based on information we consider most reliable. Our products and the information provided are intended for users with the necessary knowledge and industrial experience, and it is for these end users to determine whether the products are suitable for their use. T&H cannot control the quality and condition of the substrate, nor the various factors affecting the use of the product. Therefore, T&H accepts no liability for any loss, injury or damage arising from the use of our products or from reliance on this product data sheet (unless otherwise agreed in writing). Data in this product data sheet may be revised as necessary based on practical experience and continued product development.

Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.