Waterborne Acrylic Primer-Topcoat XH0203 is a waterborne coating. It is suitable for large vehicles, medical equipment, steel structure workshops, airport terminals and construction machinery, and other applications with high emission reduction requirements, as a weather-resistant and general corrosion-protection coating. Parameters on this page: volume solids 30 ± 3%, dry film thickness 30/40/50 µm, theoretical spreading rate 5.00 m²/L.
Parameter source: T&H original technical data sheet (TDS) for Water-borne Acrylic Primer/Topcoat XH0203; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 30 ± 3% |
|---|---|
| Dry Film Thickness | 30/40/50 µm |
| Theoretical Spreading Rate | 5.00 m2/L |
| VOC | Approx. 130 g/L |
| Density / Specific Gravity | 1.30 ± 0.20 kg/L |
| Number of Components | One-component |
| Thinner | 0-5% |
| Colour / Appearance | Various colours such as white, black and yellow |
| Wet Film Thickness | 100/135/170 µm |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Curing agent: none; thinner: deionised water
The product consists of high-quality acrylic resin, high-quality pigments (extenders), additives and water. It is suitable for large vehicles, medical equipment, steel structure workshops, airport terminals and construction machinery, and other applications with high emission reduction requirements, as a weather-resistant and general corrosion-protection coating.
| Colour | Various colours such as white, black and yellow |
|---|---|
| density | 1.30±0.20 kg/L |
| Volume Solids | 30±3% |
| Volatile Organic Compounds | Approx. 130 g/L |
| Typical dry film thickness | 40µm |
|---|---|
| Recommended dry film thickness | 30–60 µm, depending on system requirements |
| Standing time | 10-15min |
| Surface Dry | ≤30min |
| Hard dry | ≤24h |
| Thinner quantity (by volume) | Airless spray 0–5% | Air spray 0–10% | Roller or brush 0–5% |
| Recommended nozzle size | 0.3~0.4mm | 1~1.5mm | None |
| Recommended spray pressure | 15~20MPa | 0.3~0.6MPa | None |
| Application suitability | Applicable | Suitable for small-area repair | |
| Dry film thickness (µm) | 30 | 40 | 50 |
| Wet film thickness (µm) | 100 | 135 | 170 |
| Theoretical spreading rate (m²/L) | 8.33 | 6.25 | 5.00 |
The primer shall be dry, free from condensation and all contaminants. Floor coatings whose curing time has exceeded the maximum permitted interval shall be abraded with sandpaper before overcoating.
1. During application, ensure good ventilation and exhaust, keep away from ignition sources, and wear a mask, gloves and other protective equipment; adequate ventilation shall also be maintained during curing. 2. After mixing the paint with water in the specified ratio, adjust the water amount according to application requirements and temperature changes, mix thoroughly, and strain through a 120-mesh copper sieve before use. 3. Excessive thinner reduces sag resistance and slows drying. 4. During application and drying, the substrate temperature shall be above 15 °C and at least 3 °C above the dew point, and the relative humidity shall not exceed 85%. 5. When work is interrupted, do not leave paint in hoses, spray guns or spray equipment. Flush all equipment thoroughly with clean water; solvent may be used if necessary. After mixing paint with water, if work is interrupted for too long, seal and store the mixture, then re-stir before application. 6. Cleaning: all equipment may be cleaned with clean water immediately after use; solvent may be used if necessary. Periodically flushing spray equipment during the daily work is good practice. The frequency of cleaning depends on the quantity sprayed, temperature, spraying time and interruptions. 7. Remaining paint and empty cans shall be disposed of in accordance with relevant local regulations.
20kg
5–40 °C, sealed and stored in a cool place, protected from freezing, shelf life 12 months
1. The coating is water-borne but contains organic film-forming material and a small amount of volatile organic matter; inhalation of spray mist shall be avoided, and skin and eyes kept from exposure. 2. All work related to the application and use of this product shall be carried out in accordance with the relevant national health, safety and environmental standards and regulations. 3. If welding or flame cutting is required on metal coated with this product, dust and fumes will be generated; suitable personal protective equipment and adequate local exhaust ventilation are required. 4. If in doubt about the suitability of this product, consult the company.
The information provided in this product data sheet is based on laboratory test results that we consider accurate, and is provided for application guidance only. All recommendations and advice given by T&H on the use of T&H products, whether in technical documents, special consultation or otherwise, are based on information we consider most reliable. Our products and the information provided are intended for users with the necessary knowledge and industrial experience, and it is for these end users to determine whether the products are suitable for their use. T&H cannot control the quality and condition of the substrate, nor the various factors affecting the use of the product. Therefore, T&H accepts no liability for any loss, injury or damage arising from the use of our products or from reliance on this product data sheet (unless otherwise agreed in writing). Data in this product data sheet may be revised as necessary based on practical experience and continued product development.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
