Water Shield Acrylic Waterline Coating NavalGuard 5910 is an acrylic coating. An acrylic topcoat composed of acrylic resin, colouring pigments, additives, plasticiser and organic solvents, used in systems for moderate to severe corrosion environments. Parameters on this page: volume solids 46 ± 2%, dry film thickness 50/60/80 µm, theoretical spreading rate 5.7 m²/L.
Parameter source: T&H manufacturer's Technical Data Sheet (TDS) "NavalGuard 5910 Acrylic Boottop Coating"; spreading rate and other values are converted from the TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 46 ± 2% |
|---|---|
| Dry Film Thickness | 50/60/80 µm |
| Theoretical Spreading Rate | 5.7 m2/L |
| VOC | 490g/L |
| Density / Specific Gravity | 1.35kg/L |
| Number of Components | One-component |
| Flash Point | 25°C |
| Thinner | 5-15% |
| Colour / Appearance | Various colours |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Curing agent: none
An acrylic topcoat composed of acrylic resin, colouring pigments, additives, plasticiser and organic solvents, used in systems for moderate to severe corrosion environments.
| Colour | Various colours |
|---|---|
| Gloss | Semi-gloss |
| density | 1.35kg/L |
| Volume Solids | 46±2% |
| Volatile Organic Compounds | 490g/L |
| Flash Point | 25°C |
| Typical dry film thickness | 60µm |
|---|---|
| Recommended dry film thickness | 50–100 µm, depending on system requirements |
| Thinner quantity (by volume) | Airless spray 5–15% | Air spray 10–30% | Roller or brush 5–15% |
| Recommended nozzle size | 0.43~0.64mm | 1.5~2.5mm | / |
| Recommended spray pressure | 15~20MPa | 0.3~0.6MPa | / |
| Application suitability | Recommended | ||
| Dry film thickness (µm) | 50 | 60 | 80 |
| Wet film thickness (µm) | 109 | 130 | 174 |
| Theoretical spreading rate (m²/L) | 9.2 | 7.7 | 5.7 |
| Temperature | Surface Dry | Hard Dry | Pot Life | Recoat interval | |
| Minimum | Maximum* | ||||
| 5°C | 4h | 48h | / | 48h | / |
| 15°C | 2h | 36h | / | 36h | / |
| 25°C | 1h | 24h | / | 24h | / |
| 40°C | 0.5h | 16h | / | 16h | / |
*The maximum recoat interval depends on the exposure environment and the end use of the coating.
All surfaces to be coated shall be clean, dry and free from contaminants. Before coating, all surfaces shall be assessed and treated in accordance with ISO 8504:2000. Film surfaces coated with this coating, where mechanically damaged and locally rusted, shall be ground, filled or otherwise suitably treated. Surface quality may be reduced to Sa 2, but no loose powdery deposits shall be produced.
1. During application, ensure ventilation and exhaust, keep away from sources of ignition, and wear protective equipment such as masks and gloves; adequate ventilation shall also be maintained during curing. 2. Adjust the thinner quantity according to temperature changes, mix thoroughly, and filter through a 120-mesh copper sieve before use. Unused paint shall be sealed if not used for a long time, otherwise skinning may occur. If skinning occurs, filter out the skin before use. 3. The recommended thickness of one coat of this product shall not exceed 50 µm. Over-thick single coats affect curing and recoating performance and tend to cause defects such as lifting and wrinkling on recoating. This coating must not be applied over coatings containing zinc dust, nor over hot-dip galvanized, thermally sprayed zinc or aluminium surfaces, otherwise adhesion will be lost. 4. During application and curing, the substrate temperature must be above 5 °C and at least 3 °C above the dew point, and relative humidity shall not exceed 85%. Temperature and relative humidity must be measured on the substrate near the working area. 5. Cutting structures coated with this coating produces fumes; take appropriate protection. 6. When work is interrupted, do not leave coating in the paint line, spray gun or spray equipment. Flush all equipment thoroughly with thinner. If the interruption is too long, it is recommended to mix a fresh batch of paint for application. 7. Clean all equipment with thinner immediately after use. Periodically flushing spray equipment during the working day is good practice. The flushing frequency depends on the spray quantity, temperature and spray duration, including interruptions. 8. Dispose of leftover paint and empty cans in accordance with the relevant local regulations.
20kg/14.8L
Keep sealed in a ventilated, cool, dry place away from sources of ignition. Minimum 12 months.
1. For the coating and its recommended thinners, see the safety sheets and the safety data of the relevant materials. This is a solvent-borne coating; avoid inhaling spray mist and solvent vapours, and avoid exposing skin and eyes and contact with uncured paint as far as possible. 2. All work related to the application and use of this product must comply with the relevant national health, safety and environmental standards and regulations. 3. If welding or flame cutting is required on metal coated with this product, dust and fumes will be generated; use appropriate personal protective equipment and adequate local ventilation. 4. If in doubt about the suitability of this product, consult the company.
The information provided in this product data sheet is based on laboratory test results that we consider accurate, and is provided for application guidance only. All recommendations and advice given by T&H on the use of T&H products, whether in technical documents, special consultation or otherwise, are based on information we consider most reliable. Our products and the information provided are intended for users with the necessary knowledge and industrial experience, and it is for these end users to determine whether the products are suitable for their use. T&H cannot control the quality and condition of the substrate, nor the various factors affecting the use of the product. Therefore, T&H accepts no liability for any loss, injury or damage arising from the use of our products or from reliance on this product data sheet (unless otherwise agreed in writing). Data in this product data sheet may be revised as necessary based on practical experience and continued product development.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
