SIGMA ECOFLEET 530 High-activity Tin-free Self-polishing Antifouling

Browse Similar Models by Category

The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.

Introduction

A high-activity tin-free self-polishing antifouling suitable for sea areas with vigorous marine growth and shipping conditions prone to fouling.

Key properties

• A tin-free self-polishing antifouling for newbuilding and repair.
• It prevents shellfish and algal marine organisms from adhering and growing firmly on the surface; the corresponding coating system must be developed according to different ship types and shipping conditions, and the antifouling period can be up to 60 months.
• A preset polishing rate can be calculated, maintaining a smooth, highly active surface. Depending on the film thickness, it accurately provides antifouling protection over the corresponding service period and performance.
• Complies with the IMO AFS requirements for antifouling coating systems.

Colour and gloss

• Reddish brown, brown, black, blue, red pine.
• Flat

Basic data 20 °C (68 °F)

Parameters after mixing

Maximum 339.0 g/L (approx. 2.8 lb/gal) (theoretical calculated value).

China national standard GB 38469-2019 (tested value): 349.0 g/L (approx. 2.9 lb/gal)

Notes

• See the supplementary data sheet — theoretical spreading rate versus dry film thickness table.
• See supplementary parameters — recoat interval table.

Recommended substrate condition and temperature

Substrate condition

• A tie-coat compatible with high-performance anticorrosive coating systems.
• The previous coat must be sound, clean, dry and free of all contaminants.

Substrate temperature and application conditions

• During application, the substrate temperature must be maintained at least 3 °C (5 °F) above the dew point.
• During application and curing, the substrate temperature should be above -5 °C (23 °F)
• During application and curing, the relative humidity should not exceed 85%

Instructions for use

• Stir thoroughly before application.
• Before application, raise the temperature of the components or the mixed paint to above 15 °C (59 °F); otherwise, thinner may need to be added to adjust the paint viscosity to a suitable application state.
• Excessive thinning generally reduces the sag resistance of the wet film.

Airless spray (single-feed pump)

Recommended thinner

THINNER 21-06

• For local small-area repair and touch-up only.

• THINNER 21-06

Supplementary parameters

Recoat time for a coating at 150 µm (6.0 mils) dry film thickness

Notes

• The above data are for reference under normal application conditions. For film thicknesses outside the range, consult the PPG field technical service representative.
• With excessive film thickness or adverse climatic conditions, longer drying times may be required.

Safety Precautions

• This is a solvent-borne coating. Avoid inhaling spray and solvent vapours, and avoid contact of uncured paint with skin and eyes
• Refer to the Material Safety Data Sheet and product package labelling for full details of the stated safety precautions and protective measures

Worldwide applicability

Although PPG Protective & Marine Coatings is committed to providing completely consistent products to users worldwide, from time to time it may be necessary to make minor adjustments to specific products to comply with local/national regulations or environmental requirements. In the following cases, use the corresponding alternative version of the product data sheet instead.

Reference information

• Information sheet | Explanation of product data sheets

Quality guarantee

PPG warrants (1) that it has good title to the product, (2) that the product quality conforms to the relevant technical quality specifications in force at the date of manufacture of the product, and (3) that the supplied product is free of lawful claims by third parties for infringement of US patent rights. The above warranties are limited to those given by PPG and other express or implied warranties required by applicable laws and regulations for transactions and commercial practice; any abuse contrary to the stated conditions, and any other warranty for special purposes or uses, are excluded, and PPG shall be free from liability. To claim under this warranty, the buyer must notify PPG in writing within five (5) days of discovering the quality defect, and the date must be within the product's valid storage period or within one (1) year from delivery of the product to the buyer. If the buyer fails to notify PPG of the defect as required above, this will prejudice the buyer's right to obtain compensation under this warranty from PPG!

Limitation of liability

In all cases, PPG shall not be liable for any indirect, special, incidental or consequential loss of any kind arising from or in connection with the use of this product (whether based on negligence, strict liability or tort). The information in this product data sheet is based on laboratory tests we believe to be reliable, and is provided for guidance only. PPG may revise this information at any time as experience accumulates and product development progresses. All recommendations and advice concerning the use of this product, whether in technical documents, in response to an enquiry or otherwise, are given to the best of our knowledge and are believed to be reliable. Our products and related information are provided for industrial users possessing the necessary knowledge and practical skills, and it is the end user's responsibility to determine whether the product is suitable for the specific use. The buyer, having performed such evaluation, proceeds entirely at its own risk. The quality and condition of the substrate on site, and the many other factors affecting product use and application, are beyond PPG's control. Therefore, PPG accepts no liability for any loss, injury or damage arising from the use of the information in this product data sheet (unless otherwise provided in a written agreement). Different application environments, changes to the application process or extrapolation of the reference data may result in failure to achieve the expected coating quality. This product data sheet supersedes all previous versions. The buyer is responsible for confirming that the data sheet in hand is the latest version before using the product. The latest version is published on the official website of PPG Protective & Marine Coatings: www.ppgpmc.com. In case of discrepancy between the Chinese version and the original English version of the product data sheet, the English original shall prevail.

Packaging information

To meet the specific application requirements of certain countries, the following product versions may be selected

The PPG logo, and all other PPG marks are property of the PPG group of companies. All other third-party marks are property of their respective owners.