Steel: Abrasive blast cleaning to Sa 2 1/2 in accordance with ISO 8501-1. Parameters on this page: volume solids 55 ± 2%, dry film thickness 50 µm, theoretical spreading rate 5.5 m²/L/100 µm. Comparable products of the same brand and type: AMERCOAT 114 A Epoxy Filler 114 A, AMERCOAT 220 Waterborne Acrylic Topcoat 220, AMERCOAT 240 SIGMACOVER 240 High-solids Multi-purpose Epoxy Paint 240.
Parameter source: PPG manufacturer's Technical Data Sheet (TDS) "CENTRIFUGON EAP EPR"; values such as spreading rate are converted from TDS parameters and are for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | — |
|---|---|
| Dry Film Thickness | — |
| Theoretical Spreading Rate | — |
| VOC | R |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | Thinner No. 1. Application equipment thinning*, nozzle pressure |
| Packaging Specifications | 002 |
| Shelf life | .01/37 |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
Type and use: Phenolic Epoxy Coating. Substrate: steel, suitable primer or concrete. Performance: indoor ☑ outdoor ☑; approved by EDF (Électricité de France), AREVA, CEA (French Nuclear Energy Centre) for immersion and by COGEMA. Workshop application ☑ Site application ☑. Provides good chemical resistance; suitable for use in areas contaminated by aromatic, aliphatic and chlorinated solvents. New construction ☑ Maintenance ☑.
Approved for use in PIC100/101/103/104 systems (in accordance with CCTR EDF n°91C.031.05). Approved for use in EPR PIC100 systems; complies with PMUC specifications. Suitable environment: nuclear power plant characteristics (200°C – 65% RH). Product appearance: gloss. Recommended dry film thickness: 40–60 µm. Colour: refer to Feida colour card (1). Recommended wet film thickness: 70–105 µm. Components: two-component. Theoretical spreading rate: 14.5 m²/L for 40 µm dry film; 9.7 m²/L for 60 µm dry film. Mixing ratio: by volume Base 70%. Drying time: for 50 µm dry film:
Hardener: 30%. Dust-free: 1 h 30 min. Product state: thixotropic. Touch dry: 3 h. Thinner: Thinner No. 1. Handleable: 12 h. Induction time: not applicable. Pot life: CENTRIFUGON EAP itself 8 h RPE*. Ambient temperature affects pot life and minimum recoat interval. Density: 91.26 ± 0.05 00; for 50 µm dry film: 2.
Solids content: minimum 12 h – maximum 12 months 01/; by volume: 58% ± 2; by weight: 68.5% ± 2. Heat resistance 37: continuous 100°C–120°C (maximum). (Dry) D. All data relating to the density and solids content of the topcoat are based on the product being white. These data are based on mixing the product in the correct ratio.
Surface Preparation:
Steel: Abrasive blast cleaning to Sa 2 1/2 in accordance with ISO 8501-1.
Abrasive blast profile: to medium G or Ra 10–12.5 in accordance with ISO 8503-1. Primer: Epoxy: Shengbo N, Shengbo PZ, Yitelu Putty, AQUAVIGOR 696. Concrete: Ensure the surface is clean, dry and free from all contaminants. Remove all laitance and debris by washing, scraping or light abrasive blasting; ensure dust is completely removed.
Preparation of the product for use/thinning:
Stir the base mechanically, slowly adding the curing agent until fully mixed.
If required, thin the product appropriately according to the application conditions.
| Thinner: Thinner No. 1 | Cleaner: Thinner No. 1. Application equipment thinning*, nozzle pressure |
|---|
| Brush | Suitable | 0–10% (for small areas only) | ||
| Roller | Suitable | |||
| Air Spray | Suitable | 15-20% | 1.4mm | 3 - 4 bars |
| Airless Spray | Suitable | 15-20% | 0.015"– 0.017" | 180 - 200 bars |
*The thinning ratio is adjusted according to weather and specific application conditions.
Application conditions:
| Ambient temperature: +5 °C to +35 °C | Relative humidity below 80%. Substrate temperature: minimum +5°C and at least +3°C above dew point; maximum +35°C. Product temperature should be above 10°C. Note: (1) Two coats may be required to achieve full hiding. Some colours can only be matched approximately to the physical colour card and may be subject to a minimum order quantity of 100–200 L. |
|---|
Health and safety; flash point:
| Base and hardener: 21 °C < flash point < 55 °C | Thinner No. 1: 21 °C < flash point < 55 °C |
|---|---|
| Organic volatile content per litre: 428 g/L | Item |
| VOC data vary slightly depending on colour and thinner used. | R |
| MSDS available at www.quickfds.com (Supplier FREITAG) | PE for packaging and storage, suitable 9 |
| Packaging: 20 L (Base: 14 L / Hardener: 6 L), 5 L (Base: 3.5 L / Hardener: 1.5 L) | 002 |
| Storage: unopened indoors between +5°C and +35°C. For shelf life, refer to the product label. | .01/37 |
| AFNOR classification (NFT 36005): | Class I, grade 6b, D |
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
