ZIES214 Inorganic Zinc-rich Shop Primer is a zinc-rich primer. A shop primer designed for automatic spray lines, providing short- to medium-term protection for blast-cleaned steel plates or other steel structures during storage, construction and assembly. It has the advantages of weather resistance, good welding and cutting performance, small burn-off area, good heat resistance and long protection period. Parameters on this page: dry film thickness 15–20 µm, theoretical spreading rate 14.36 m²/kg.
Parameter source: OSAKA original technical data sheet (TDS) "ZIES214 Inorganic Zinc-rich Shop Primer"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 63% |
|---|---|
| Dry Film Thickness | 15–20 µm |
| Theoretical Spreading Rate | 14.36 m²/kg |
| VOC | 318 g/L |
| Density / Specific Gravity | Approx. 2.80 kg/L |
| Number of Components | Two-component |
| Thinner | OUP 107 |
| Mixing Ratio | ZIES214 : ZIES218 = 2 : 1 |
| Pot Life | 23 °C: 24 h |
Zinc dust-containing shop primer, grey. It has the advantages of weather resistance, good welding and cutting performance, small burn-off area, good heat resistance and long protection period.
A shop primer providing short- to medium-term protection for blast-cleaned steel plates or other steel structures during storage, construction and assembly, designed specifically for automatic spray lines.
| Volume Solids | 63% |
|---|---|
| Dry Film Thickness | 15–20 µm |
| Theoretical Spreading Rate | 14.36 m²/kg |
| Practical Spreading Rate | Allowing a suitable loss |
| Volatile organic compound content | 318 g/L |
| Mixing Ratio | ZIES214 : ZIES218 = 2 : 1 |
|---|---|
| Airless spray | Recommended: tip size 0.48–0.58 mm; fluid pressure ≥ 8 MPa |
| Brush or roller | May be used, for touch-up only. |
| Conventional spray | Suitable, but requires suitable equipment with an agitator. |
| Thinner | OUP 107 |
| Paint equipment cleaner | OUP 107 |
| Pot life | 23 °C: 24 h |
| Drying Time | ||||
| Substrate Temperature | Touch dry (min) | Hard dry (h) | Recoat Interval | |
| Minimum | Maximum | |||
| 5°C | 5 | 24 | 24 h | Unlimited |
| 23°C | 3 | 16 | 16 h | Unlimited |
| 35°C | 2 | 12 | 12 h | Unlimited |
| Storage | Store in a cool, dry environment |
|---|---|
| Shelf life | 1 year |
| Packaging Specifications | 18 kg in a 20 L container |
| Flash Point | Greater than 13 °C (mixture) |
| density | Approx. 2.80 kg/L |
Steel surfaces: remove oil and grease with a suitable cleaner, then blast to Sa2.5 of ISO 8501:2007, with a surface profile of 40–75 µm.
The surface temperature to be coated shall be above the dew point to avoid condensation. The minimum overcoating interval depends on temperature and air relative humidity; the maximum overcoating interval depends on climatic and environmental conditions. Surfaces coated with this product shall be clean, dry and free from zinc salts before overcoating. Overcoating with alkyd, oil-based coatings and the like is not recommended.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
