HI-EPOXY 1410 Multi-purpose Primer is an epoxy paint used as a primer. A multi-purpose protective primer with high compatibility performance, used as a rust-preventive tie primer on steel structures, galvanized, aluminium alloy, stainless steel and copper surfaces of electrical equipment, instruments and construction machinery in moderate corrosion environments. Fast drying, high application performance, good adhesion, suitable for various substrates. 550 g/L. Surfaces to be coated shall be clean, dry and free from contamination. Parameters on this page: volume solids 40 ± 2%, DFT 15–35 µm, theoretical spreading rate 0.10 kg/m².
Parameter source: Nippon Paint Industrial NIPPON INDUSTRIAL original technical data sheet (TDS) "HI-EPOXY 1410 Multi-purpose Primer"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 40 ± 2% |
|---|---|
| Dry Film Thickness | 15-35µm |
| Theoretical Spreading Rate | 0.10 kg/m² |
| VOC | 550 g/L |
| Density / Specific Gravity | 1.32kg/L |
| Number of Components | One-component |
| Thinner | Thinner 0941 |
| Mixing Ratio | This product is one-component; no mixing required. |
| Colour / Appearance | Grey-white |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
HI-EPOXY 1410 is a one-component primer based on a specially modified epoxy resin. The product dries fast
and offers high application performance and good adhesion, suitable for various substrates.
A multi-purpose protective primer with high compatibility performance, used as a rust-preventive tie primer on steel structures, galvanized, aluminium alloy, stainless steel and copper surfaces of electrical equipment, instruments and construction machinery in moderate corrosion environments.
| Colour | Grey-white |
|---|
| Solids content (by volume) | 40±2% |
|---|---|
| Density | 1.32kg/L |
| VOC | 550 g/L. Surfaces to be coated shall be clean, dry and free from contamination. Surface evaluation and cleaning shall refer to ISO 8504. Oil and |
Remove oil and grease in accordance with SSPC-SP1 solvent cleaning.
Carbon steel surface preparation: blast cleaning to Sa 2½ (ISO 8501-1:2007) or SSPC-SP6 (SSPC-SP10 gives better results). If oxidation has occurred on the blasted surface before application, the surface must be re-treated to the specified standard. Surface defects exposed after blasting shall be treated by grinding, filling or other suitable methods. A surface profile of 40–75 µm is preferred.
Galvanized and aluminium alloy surfaces: this product may be used on galvanized and aluminium alloy surfaces. Before application, light sweep blasting with a fine non-metallic abrasive such as quartz sand, followed by cleaning, is required before spraying the product.
Repair of damaged areas: on carbon steel, rust products must be removed from the surface and the area cleaned to Sa 2½. Where blast cleaning is not possible in local areas, mechanical grinding to St3 (ISO 8501-1:2007) is permitted.
For galvanized and aluminium alloy surfaces, abrading and cleaning of surface contaminants are required before repair with HI-EPOXY 1410.
Before application of HI-EPOXY 1410, ensure the surface to be coated is clean and dry, and application must be carried out within the specified recoat interval (refer to the relevant product application instructions).
Other surfaces: if this coating is to be applied to other surfaces, consult the local Nippon Paint company for further information.
Application is not recommended when substrate temperature is above 45°C or relative air humidity is above 85%; steel plate temperature shall
at least 3 °C above the ambient dew point, and ensure good ventilation at the application site.
| Mixing ratio | This product is one-component; no mixing required. |
|---|---|
| Theoretical spreading rate | 0.10 kg/m² (at 30 µm DFT) |
| Thinner | Thinner 0941. Thinning must not exceed the limits of local regulations. |
Roller/brush/air spray: for touch-up and small-area application;
Airless spray: recommended for large-area application;
Regardless of the method used, the specified dry film thickness must be achieved.
| Airless Spray | Nozzle tip size: 0.015" – 0.021" : Nozzle pressure: 120- kg/cm² |
|---|---|
| Typical film thickness | 15 - 35 µm DFT : 38 - 88 µm WFT Drying time * |
| Substrate Temperature | 15°C | 25°C | 40°C |
| Touch dry time | 30min | 15min | 5min |
| Hard dry time | 4h | 2h | 1h |
| Minimum recoat time | 4h | 2h | 1h |
| Maximum recoat time * | - | ||
The above data are for reference only; actual overcoating and drying times may be shorter or longer depending on film thickness, ventilation, humidity, coating system and prior hand or mechanical preparation.
The following intermediate coats/topcoats may be used with HI-EPOXY 1410 zinc phosphate epoxy primer:
Intermediate Coat
Topcoat
The coating system may be selected according to the specific situation; for detailed coating system information, contact Nippon Paint for professional guidance.
Kit Weight Packaging Size 20kg 20kg 18L
| Shelf life (from date of production) | 12 months (25 °C) |
|---|
Store in accordance with national regulations. The product shall be kept sealed in a dry, cool and well-ventilated warehouse, away from heat and ignition sources. Excessively high temperatures shorten the storage period and may cause gelling of the paint in the can. The above is the minimum shelf life; beyond this period, testing is required to determine whether the product can still be used.
▪ For professional use only. Refer to the safety information on the packaging and the Safety Data Sheet (SDS) before use.
All information in this product data sheet is based on laboratory tests and practical experience. However, since the product is subject to many unforeseeable and uncontrollable factors in actual use, we guarantee only the quality of the product itself. Read this data sheet carefully and confirm with Nippon Paint that it is the latest version before using the product.
We reserve the right to modify this product data sheet without prior notice.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
