The first coat yellow has visible film thickness measurement (SI) technology, allowing the applicator to visually confirm during application whether the correct film thickness (wet/dry) has been applied. Parameters on this page: number of components: two.
Source: NIPPON MARINE original technical data sheet (TDS) 'NOA FWT Solvent-free Epoxy Paint for Potable Water Tanks'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 69% |
|---|---|
| Dry Film Thickness | 125 µm (yellow); 75–125 µm (blue, white, cream) |
| Theoretical Spreading Rate | 5.52 m²/L |
| VOC | 343 g/L |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | THINNER 670 |
| Mixing Ratio | Volume mixing ratio: base 3.7 / curing agent 1 |
| Colour / Appearance | (visible film thickness measurement (SI) technology / first coat) yellow (non-visible film thickness measurement (SI) technology / seco… |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
| Publication date | July 2024. NOA FWT is a two-component pure epoxy anti-rust paint for fresh water and potable water tanks. The first coat yellow has visible film thickness measurement (SI) technology, allowing the applicator to visually confirm during application whether the correct film thickness (wet/dry) has been applied. The two-coat system is: first coat SI technology (yellow); second coat non-SI technology (blue, white, cream). |
|---|
Product Data
Anti-rust protection for potable water tanks and lubricating oil tanks
| Type | Pure epoxy (two-component) |
|---|---|
| Colour | (visible film thickness measurement (SI) technology / first coat) yellow; (non-visible film thickness measurement (SI) technology / second coat) blue, white, cream |
| Gloss | Semi-gloss |
| Volume Solids | 69% (ISO3233:1998) |
| Dry Film Thickness | 125 µm (yellow); 75–125 µm (blue, white, cream) |
| Wet Film Thickness | 181 µm (yellow); 109–181 µm (blue, white, cream) |
| Theoretical Spreading Rate | 5.52 m²/L (yellow/125 µm); 9.20 m²/L (blue, white, cream/75 µm) |
| Drying Time | Surface Dry | 3.5 h (5 °C) | Hard Dry | 36 h (5 °C) |
| 1.5 h (20 °C) | 16 h (20 °C) | |||
| 40 min (30 °C) | 10 h (30 °C) | |||
| Recoat interval | Minimum | 36 h (5 °C) | Maximum | 10 days (5 °C) |
| (self-recoat) | 16 h (20 °C) | 7 days (20 °C) | ||
| 10 h (30 °C) | 5 days (30 °C) |
| VOC | 343 g/L (GB/T 23985-2009) |
|---|
Blast-clean to ISO Sa 2.5, or power tool clean to ISO St 3.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure fresh water to remove all grease, soluble salts and foreign matter.
| Thinner | THINNER 670 |
|---|
Airless Spray
| Gun tip size | 0.48 ~ 0.53 mm |
|---|---|
| Spray fan angle | 45° ~ 60° |
| (repair) | 30° |
| Output pressure | 150–250 kg/cm². Brush: for small-area repair only |
| Mixing ratio | Volume mixing ratio: base 3.7 / curing agent 1 |
5 h (5 °C)
| 3 h | (20°C) |
|---|---|
| 2.5 h | (30°C) |
| Packaging Specifications | Two-component: 20 L (base 15.7 L, hardener 4.3 L); packaging may vary by production location |
|---|---|
| Flash Point | Base: 26.0 °C, hardener: 27.0 °C (GB/T 5208-2008) |
Take the necessary protective measures to avoid skin and eye contact (e.g. gloves, safety glasses, face shield, barrier cream).
Ensure adequate ventilation during application and drying to keep solvent vapour concentrations within safe limits.
Before use, refer to the health and safety information in the Safety Data Sheet (SDS) for this product.
Precautions:
| 1. | The contents of this product data sheet may change at any time as experience grows and the product develops. |
|---|---|
| 2. | Maintain adequate ventilation during and after application. |
| 3. | For removing soluble substances, solvent residues and other related matters, refer to the 'NOA FWT Potable Water Tank Coating Application Specification'. |
| 4. | Allow at least 7 days (20 °C) drying before loading potable water. |
| 5. | If UV disinfection is used in the tank, consult NIPPON MARINE personnel first. |
| 6. | For selection of this product, consult the local NIPPON MARINE personnel. |
| 7. | Packaging containers and can sizes may vary by local regulations. |
| 8. | This product should be stored in a paint warehouse. |
| 9. | Outside China, use THINNER 600 in place of THINNER 615. |
10. Clean spray equipment with a solvent complying with local regulations.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
