NIPPON U-MARINE FINISH Polyurethane Topcoat is a topcoat. A topcoat for freeboards, superstructures and similar areas. A polyurethane topcoat with excellent weatherability and colour retention; the white version of this product holds a leading position worldwide. Parameters on this page: volume solids 62 ± 2%, theoretical spreading rate 20.66 m²/L (30 µm), number of components two.
Source: NIPPON MARINE original technical data sheet (TDS) "NIPPON U-MARINE FINISH Polyurethane Topcoat"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 62 ± 2% |
|---|---|
| Dry Film Thickness | 25-50µm |
| Theoretical Spreading Rate | 20.66 m²/ℓ (30µm) |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | THINNER 700 (5–15%, by weight) |
| Mixing Ratio | Base : curing agent = 16.7 : 3.3 |
| Colour / Appearance | White 000 base – FGN095, black 999 base – FGN01… |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A polyurethane topcoat with excellent weatherability and colour retention; the white version of this product holds a leading position worldwide. Can be used in combination with other products, with NOA series products and epoxy anticorrosive as primer.
A topcoat for freeboards, superstructures and similar areas
| Type | Polyurethane (high-build/two-component) |
|---|---|
| Colour | White 000 base – FGN095; black 999 base – FGN010. Grey 060 base – FGN060; light grey 070 base – FGN070. Green 442 base – FGS442; green 225 base – FGN225. Yellow 355 base – FGJ355. Iron red 445 base – FGJ445. Orange 592 base – FGJ592. Other colours: curing agent – FGA315 |
| Gloss | |
| Solids content (by volume) | 62 ± 2% (ISO3233:1998) |
| Mixing ratio (by volume) | Base : curing agent = 16.7 : 3.3 |
| Recommended film thickness | Dry film: 25–50 µm |
| Wet film | 40 ~ 81µm |
| Theoretical Spreading Rate | 20.66 m²/ℓ (30µm) |
| Thinner | THINNER 700 (5–15%, by weight) |
| 5°C | 20°C | 30°C | ||
| Drying Time | Surface Dry | 40 min | 30 min | 10 min |
| Hard Dry | 16 h | 8 h | 6 h | |
| Fully cured | 14 days | 7 days | 5 days | |
| Recoat interval | Minimum | 24 h | 16 h | 12 h |
| (self-recoat) | Maximum | ----- | ----- | |
| Pot life | 10 h | 5 h | 3 h |
| Flash Point | Base 33 °C, curing agent 73 °C |
|---|
Airless spray, tip size: 0.38–0.48 mm
| Spray fan angle | 55 ~ 60° |
|---|---|
| Output pressure | 120 ~ 150 kg/㎝2 |
| Brush/roller | For small-area repair only |
All surfaces to be coated must be kept clean, dry and free from contaminants
| Packaging Specifications | 20 L (base 16.7 L, curing agent 3.3 L) |
|---|
Take the necessary protective measures to avoid skin and eye contact (e.g. gloves, safety glasses, face shield, barrier cream). Ensure adequate ventilation during application and drying to keep solvent vapour concentrations within safe limits.
Before use, refer to the health and safety information in the Material Safety Data Sheet (MSDS) for this product.
1) The content of this product datasheet may change at any time as our experience grows and the product is further developed. 2) For application at high temperature, use THINNER 750. 3) Store this product in a paint warehouse.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
