NIPPON E-MARINE A/C II M antifouling belongs to antifouling coatings. Parameters on this page: volume solids 63 ± 2%, dry film thickness 50-125 µm, theoretical spreading rate 8.42 m²/L.
Parameter source: nippon-marin manufacturer's Technical Data Sheet (TDS) "NIPPON E-MARINE A/C II M Antifouling"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 63 ± 2% |
|---|---|
| Dry Film Thickness | 50-125 µm |
| Theoretical Spreading Rate | 8.42 m²/L (75 µm) |
| VOC | 371 g / L |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | NIPPON MARINE THINNER 615 |
| Mixing Ratio | BASE 7 / HARDENER 1 |
| Colour / Appearance | Grey |
| NIPPON | E-MARINE |
|---|
A/CⅡM A two-pack epoxy tie-coat anticorrosive designed especially for maintenance & repair application at Dry Dock. The combination with effective anti-corrosive primers, the system provides excellent seawater resistance and good adhesion property to various kinds of antifoulings and finishes with optimized overcoating intervals.
For Maintenance & repair as at Dry Dock As Tie-coat anticorrosive for outer hull (including boottop and topsides), decks, superstructure, etc.
| Type | Epoxy (Two-pack / High build) |
|---|---|
| Color | Grey |
| Gloss | Flat |
| Volume Solids | 63 ± 2% (ISO3233:1998) |
| Typical Dry Film Thickness | 50 ~ 125 µm |
| Approx. Wet Film Thickness | 79 ~ 198 µm |
| Theoretical Coverage | 8.42 m²/L (75 µm) |
as supplied
| Drying Time | Surface Dry | 5 hours (5°C) | 2 hours (20°C) | 1 hour (30°C) |
| Dry Hard | 24 hours (5°C) | 14 hours (20°C) | 10 hours (30°C) | |
| Interval before Overcoating | Min. | 5 hours (5°C) | 3 hours (20°C) | 2 hours (30°C) |
| (by self) | Max. | - (5°C) | - (20°C) | - (30°C) |
| VOC Values | 371 g / L |
| Thinner | NIPPON MARINE THINNER 615 |
|---|
Airless Spray
| Tip range | 0.48 ~ 0.59 mm |
|---|---|
| Fan angle | 55° ~ 62° |
| (For T/U) | 30° |
| Output pressure | 150 ~ 200 kg/cm² |
| Brush | For touching up small areas only |
| Mixing Ratio by Volume | BASE 7 / HARDENER 1 |
| Pot Life after Mixing | 6 hours (5°C) |
| 3 hours (20°C) | 2 hours (30°C) |
| Packaging | Two Packs - 20L (base 17.5L, HARDENER 2.5L) |
| Flash Point | BASE 24°C, HARDENER 42°C |
All surfaces to be coated should be clean, dry and free from contamination.
High pressure fresh water wash and remove all oil / grease, soluble contaminants and other foreign matters.
Take precautions to avoid skin and eye contact (i.e. gloves, goggles, face masks, barrier creams etc.) Proper ventilation and protective measures must be provided during applications and drying period to keep solvent vapor concentrations within safe limits.
Prior to use, obtain, consult and follow the SDS for this product concerning health and safety information.
1)The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.
2)Prior to overcoating, remove heavily chalked layer, salt contamination, etc. by fresh water washing.
3) For availability of product consult Nippon Paint Marine representatives.
4) Unit size and filled volumes can vary due to local regulations.
5) Store the paints in paint store.
6) Use products that comply with local regulations to clean the paint equipment.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
