NIPPON A-MARINE FINISH H Hull Topcoat is a topcoat. (GB 38469-2019) issued by People's Republic of China. Parameters on this page: volume solids 50 ± 2%; dry film thickness 30–50 µm; theoretical spreading rate 14.29 m²/L.
Source: NIPPON MARINE original technical data sheet (TDS) 'NIPPON A-MARINE FINISH H Hull Topcoat'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 50 ± 2% |
|---|---|
| Dry Film Thickness | 30-50 µm |
| Theoretical Spreading Rate | 14.29 m²/L (35 µm) |
| VOC | 448 g / L |
| Density / Specific Gravity | — |
| Number of Components | — |
| Flash Point | 32°C |
| Thinner | NIPPON MARINE THINNER 200 |
| Colour / Appearance | Other colors |
| NIPPON | A-MARINE |
|---|---|
| FINISH | H A high solid acrylic based finish with good weathering resistance and workability. |
| It | satisfies regulation value in the "Limit of harmful substances of marine coatings" |
(GB 38469 2019) issued by People's Republic of China.
Finish for boottop, topsides, decks, superstructures, etc.
| Type | Acrylic White, Black, 445 Red Oxide, Gray*, Cream*, Blue*, Green*, |
|---|---|
| Color | Other colors |
(see Note 3)
| Gloss | Semi-gloss |
|---|---|
| Volume Solids | 50 ± 2% (ISO3233:1998) |
| Typical Dry Film Thickness | 30 ~ 50 µm |
| Approx. Wet Film Thickness | 60 ~ 100 µm |
| Theoretical Coverage | 14.29 m²/ L (35 µm) |
as supplied
| Drying Time | Surface Dry | 40 minutes (5°C) | 20 minutes (20°C) | 15 minutes (30°C) |
| Dry Hard | 2 hours (5°C) | 1 hour (20°C) | 30 minutes (30°C) | |
| Interval before Overcoating | Min. | 6 hours (5°C) | 3 hours (20°C) | 2 hours (30°C) |
| ( by self ) | Max. | ― (5°C) | ― (20°C) | ― (30°C) |
| VOC Values | 448 g / L |
| Thinner | NIPPON MARINE THINNER 200 |
|---|
Airless Spray
| Tip range | 0.43 ~ 0.48 mm |
|---|---|
| Fan angle | 55 ~ 69° |
| Output pressure | 100 ~ 150 kg / cm² |
| Brush | For touching up small areas only |
| Package | 20L |
| Japan Local Brand | NIPPON A-MARINE FINISH H |
| Flash Point | 32°C |
All surfaces to be coated should be clean, dry and free from contamination.
High pressure fresh water wash and remove all oil / grease, soluble contaminants and other foreign matters.
Take precautions to avoid skin and eye contact (i.e. gloves, goggles, face masks, barrier creams etc.) Proper ventilation and protective measures must be provided during applications and drying period to keep solvent vapor concentrations within safe limits.
Prior to use, obtain, consult and follow the SDS for this product concerning health and safety information.
1)The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.
2)Use NIPPON MARINE THINNER 200 to wash painting appliances, hoses and guns before and after use.
3) Chlorinated rubber paints should not be applied on top of A-marine finish.
4) The following colours are available as our standard.
| Gray | 070, 065, 060, 055, 050, 040 |
|---|---|
| Cream | 332, 335 |
| Blue | 606, 808, 837 |
| Green : | 442, 505, 535, 225 5) For availability of product consult Nippon Paint Marine representatives. |
6) Unit size and filled volumes can vary due to local regulations.
7) Store the paints in paint store.
8) The coating film may soften when exposed to heat sources such as direct sunlight, due to the general thermoplasticity of acrylic resin. This can result in surface stickiness, visible footprints, or dust accumulation on the coating surface. Allow the coating to recover naturally as it cools.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
