Suitable for exposed decks, walkways, vehicle decks, helicopter decks and vehicle passageways requiring stable trafficability; two types of aggregate (coarse/fine) are available according to the requirements of the coated area. Parameters on this page: volume solids 78 ± 2%, dry film thickness 600 µm, theoretical spreading rate 1.30 m²/L.
Parameter source: nippon-marin original technical data sheet (TDS) “NEOGUARD SPIKE Anti-slip Epoxy Coating”; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 78 ± 2% |
|---|---|
| Dry Film Thickness | 600 µm |
| Theoretical Spreading Rate | 1.30 m²/L (600 µm) |
| VOC | 192 g/L |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | No thinning required; for equipment cleaning use THINNER 615 |
| Mixing Ratio | Volume mixing ratio: base 4 / curing agent 1 |
| Colour / Appearance | Green, grey |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
| Publication date | July 2024 NEOGUARD SPIKE is a deck anti-slip coating containing special epoxy resin and hard alumina aggregate, designed with full consideration of safe operation, featuring good anti-slip performance and excellent water resistance, seawater resistance, abrasion resistance and impact resistance. Suitable for open decks, walkways, vehicle decks, helicopter decks and vehicle passageways requiring traffic stability; two types of aggregate (coarse/fine) are available according to coating area requirements. |
|---|
| Recommended use | Suitable for surfaces requiring anti-slip performance |
|---|---|
| Type | Epoxy (high-build/abrasion-resistant/anti-slip/two-component) |
| Colour | Green, grey |
| Gloss | Flat |
| Volume Solids | 78 ± 2% (ISO3233:1998) |
| Dry Film Thickness | 600 µm |
| Wet Film Thickness | 769 µm |
| Theoretical Spreading Rate | 1.30 m²/ L (600 µm) |
Drying Time Hard Dry
| Surface Dry | 5 h (5 °C) | 24 h (5 °C) |
| 2 h (20 °C) | 12 h (20 °C) | |
| 1.5 h (30 °C) | 10 h (30 °C) | |
| Fully cured | 14 days (5 °C) |
| 7 days | (20°C) |
|---|---|
| 5 days | (30°C) |
Minimum; maximum
| Recoat interval | 18 h (5 °C) | -- (5°C) |
| (self-recoat) | 10 h (20 °C) | -- (20°C) |
| 8 h (30 °C) | -- (30°C) |
| VOC | 192 g/L (GB/T 23985-2009) |
|---|
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure fresh water to remove all grease, soluble salts and foreign matter.
| Thinner | No thinning required; for equipment cleaning use THINNER 615 |
|---|
Special spray equipment, trowel, roller
| Mixing ratio | Volume mixing ratio: base 4 / curing agent 1 |
|---|---|
| Pot life | 9 h (5 °C) |
| 4 h | (20°C) |
| 2 h | (30°C) |
| Packaging Specifications | Two-component: 16 L (Base 12.8 L, Curing Agent 3.2 L); packaging may vary depending on place of origin |
| Flash Point | Base: >50.0 °C, curing agent: 25.0 °C (GB/T 5208-2008) |
Take the necessary protective measures to avoid skin and eye contact (e.g. gloves, safety glasses, face shield, barrier cream).
Ensure adequate ventilation during application and drying to keep solvent vapour concentrations within safe limits.
Before use, refer to the health and safety information in the Safety Data Sheet (SDS) for this product.
Precautions: 1. The content of this product data sheet may be revised at any time as our experience grows and the product is further developed.
2. The aggregate may float on the surface of the base; the base and curing agent must be completely mixed and thoroughly stirred before application.
3. This product must have sufficient roughness to produce a reliable anti-slip effect; fully estimate paint consumption during use.
4. For selection of this product, consult local Nippon Paint Marine coatings personnel.
5. Packaging containers and can quantities may vary due to local regulatory requirements.
6. This product shall be stored in a paint warehouse.
| 7. For countries and regions outside China, use THINNER | 600 replaces THINNER 615. |
|---|
8. Clean spray equipment with solvents meeting local regulatory requirements.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
