ECOLOFLEX SPC 150 HyB Tin-Free Self-Polishing Antifouling 150 HyB is an antifouling. The product uses patented metallic copper silyl acrylate polymer technology, keeping the active surface of the coating layer continuously exposed to seawater through the stable low friction of the coating, thereby achieving excellent antifouling performance. Parameters on this page: volume solids 60 ± 2%, theoretical spreading rate 6.0 m²/L (100 µm dry film).
Parameter source: Nippon Marine original technical data sheet (TDS) for ECOLOFLEX SPC 150 HyB Tin-Free Self-Polishing Antifouling 150 HyB; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 60 ± 2% |
|---|---|
| Dry Film Thickness | 65µm ~ 150µm |
| Theoretical Spreading Rate | 6.0 m²/L (100 µm dry film) |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | — |
| Flash Point | 24°C |
| Thinner | THINNER 300 (thinning by volume: 0–5%) |
| Colour / Appearance | Brown B – BRB013 Light brown B – BRB027 Brown C – BR… |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
The product uses patented metallic copper silyl acrylate polymer technology, keeping the active surface of the coating layer continuously exposed to seawater through the stable low friction of the coating, thereby achieving excellent antifouling performance.
Antifouling for ocean-going vessels
| Type | Copper silyl acrylate polymer (tin-free/low friction/hydrolysing/high solids) |
|---|---|
| Colour | Brown B – BRB013 Light brown B – BRB027 Brown C – BRB003 Light brown C – BRB017 |
| Gloss | Semi-gloss |
| Solids content (by volume) | 60 ± 2% (ISO3233:1998) |
| Recommended film thickness | DFT: 65–150 µm |
| Wet film | 108µm ~ 250µm |
| Theoretical Spreading Rate | 6.0 m²/L (100 µm dry film) |
| Thinner | THINNER 300 (thinning by volume: 0–5%) |
| 5°C | 20°C | 30°C | ||
| Drying parameters | Surface Dry | 1 h | 40 min | 30 min |
| Hard Dry | 3 h | 1 h | 40 min | |
| Recoat interval | Minimum | 6 h | 4 h | 3 h |
| (self-recoat) | Maximum | ----- | ----- | |
| Interval before immersion (100 µm) | 18 h | 12 h | 10 h |
※See note 4)
| Flash Point | 24°C |
|---|
Airless spray: tip size 0.69–0.84 mm
| Spray fan angle | 60 ~ 75° |
|---|---|
| Output pressure | Greater than 200 kg/cm² |
| Brush/roller | For small-area repair only |
All surfaces to be coated must be clean, dry and free of contaminants. Wash with high-pressure fresh water to remove all oil, grease, soluble salts and foreign matter
| Packaging Specifications | 20 L (packaging may vary by origin) |
|---|
Take the necessary protective measures to avoid contact with skin and eyes (e.g. gloves, protective goggles, face protection). Before use, refer to the material safety data sheet (MSDS) of this product for health and safety information.
1) The content of this product data sheet may be revised at any time as our experience grows and the product is further developed.
2) Before and after use, clean spray equipment, hoses and spray guns with THINNER 300.
3) If mixed with other antifoulings or any other chemicals, the product will not qualify for the 'tin-free antifouling declaration'.
4) The interval before immersion depends on the surrounding environmental conditions, ventilation, film thickness and number of coats, and is affected accordingly. Contact us during actual application.
5) Store the product in a paint warehouse.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
