TANKCARE PC-50 Phenolic Epoxy Paint PC-50 is an epoxy coating. Vessels. A primer-topcoat coating used as the interior lining of tanks and vessels. A two-component high-build epoxy phenolic tank coating. High chemical and solvent resistance. Excellent high-build applicability. Excellent anti-abrasion and impact resistance. Parameters on this page: volume solids 70 ± 2%; dry film thickness 100–300 µm per coat; theoretical spreading rate 0.296 kg/m²/150 µm.
Source: KANSAI original technical data sheet (TDS) 'TANKCARE PC-50 Phenolic Epoxy Paint PC-50'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 70 ± 2% |
|---|---|
| Dry Film Thickness | 100–300 µm per coat |
| Theoretical Spreading Rate | 0.296 kg/m²/150 µm |
| VOC | 300 g/L, complying with EU Solvent Emissions Directive 2004/42/EC, subcategory j |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Flash Point | Above 25 °C |
| Thinner | Epoxy Thinner #20 |
| Mixing Ratio | Base/Hardener=9/1(by weight) |
| TANKCARE PC-50 | Phenolic Epoxy PC-50 |
|---|
A two pack hi-build epoxy novolac tank coating.
As a protective primer-finish coat can be used for internal lining of tanks and
Complies with SY/T 0319-98, SY/T 0320-2010
Excellent resistance to extensive range of solvents and chemicals
| Color | Grey and White |
|---|---|
| Colour | Grey and white |
| Volume Solids | 70±2 % |
| VOC | 300g/L,accord with EU Dircrtive2004/42/EC,subcategory j |
| Volatile organic compound content | 300 g/L, complying with EU Solvent Emissions Directive 2004/42/EC, subcategory j |
| Flash Point | Greater than25°C |
| Flash Point | Above 25 °C |
| Film thickness | Dry 100-300 microns/coat Wet : 125-375microns/coat |
| Applied film thickness | DFT: 100–300 µm per coat; WFT: 125–375 µm per coat |
| Theoretical Coverage | 0.296Kg/m2/150 microns |
| Theoretical spreading rate | 0.296 kg/m²/150 µm |
Practical coverage depending on surface conditions, environment, applications, etc.
| SURFACE PREPARATION | Remove salt and other water-soluble contaminants by fresh water. |
|---|---|
| Surface Preparation | Rinse off salts and other water-soluble contaminants with clean water. |
Remove oil and grease with suitable detergent or solvent(SSPC-SP 1).
Remove rust, mill-scale and other loose material completely by abrasive blasting.
All surface to be coated should completely clean, dry and free from contamination.
| Application Temperature | 10°C-40°C |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| Mixing | Mix the base and curing agent and stir thoroughly with a power tool |
| Mixing Ratio | Base/Hardener=9/1(by weight) |
| Mixing ratio | Base : curing agent = 9:1 (by mass) |
| Pot life | 5°C | 20°C | 30°C |
| Pot life | 5hrs | 4hrs | 3hrs |
| Application Methods | Airless spray, air spray |
|---|---|
| Application Methods | Airless spray, air spray |
Airless spray
| Nozzle tip | Nozzle size | 0.43mm-0.53mm |
| Nozzle pressure | Output pressure | ≥10Mpa |
| Thinning ratio | 0–5% by volume |
Brush/Roller; Thinning ratio 5–10% by volume
| Thinner | Epomarine Thinner #20 |
|---|---|
| Thinner | Epoxy Thinner #20 |
| Drying time & Overcoating interval | Drying time & Surface dry | Drying time & touch dry | 15°C 24hrs | 25°C 4hrs | 35°C 4hrs |
| Drying time & recoat interval | Touch dry | Semi-hard dry | 48hrs | 24hrs | |
| Min. interval | Minimum recoat interval | 48hrs | 24hrs | ||
| Max. interval | Maximum recoat interval | 7days | |||
| Applied Substrate | Bare steel |
|---|---|
| Suitable substrates | Bare steel |
| Typical topcoat | TANKCARE PC-50 |
| Suitable for overcoating | Phenolic Epoxy PC-50 |
Store in dry, cool condition and away from sources of heat and ignition. Containers
must be kept tightly closed.
| Shelf life | 12 months from date of production (25°C) |
|---|---|
| Shelf life | 12 months from date of production (25 °C) |
| SAFETY PRECAUTIONS | Detail information is given on MSDS. |
| Safety measures | For details, see the Safety Data Sheet. |
Avoid inhalation of spray mist or vapour.
Avoid skin and eye contact.
Paint contacted with skin should be immediately removed with water and/or suitable cleanser. Eyes should be flushed with water and seek immediate medical attention.
Since this product contains flammable solvents, keep away from sparks and open flames.
Application and handling of this product should be in compliance with relevant national regulations.
The information given on this sheet is to the best of our knowledge and accurate at
the time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
The information provided in this data sheet is, to the best of our knowledge, the most complete and accurate information currently available. As the conditions of product use are beyond our control, this information carries no warranty, and we are responsible to the buyer only in the selection of the product. As our products and production processes are continuously developed, the content of this data sheet is subject to change at any time, and all information herein is subject to our confirmation. Confirm that the data sheet in hand is the latest version before using the product.
| Issued Date | 2014/03/02 |
|---|---|
| Issue date | 2014/03/02 |
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
